<div dir="ltr">Dave, you're a rock star :)<div><br></div><div>Incidentally, I've heard there's a common trick with diodes done in most designs to protect the 2164 from frying by getting power on one rail before another (or something like that). Can somebody explain that better to me?</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Jun 26, 2017 at 11:42 PM, David G Dixon <span dir="ltr"><<a href="mailto:dixon@mail.ubc.ca" target="_blank">dixon@mail.ubc.ca</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><u></u>





<div dir="ltr">
<div dir="ltr" align="left"><span class="m_4864580003579947465857172704-27062017"><font color="#0000ff" size="2" face="Arial">You should also realize that the 2164 is a current amp.  
I know that the datasheet says that the absolute maximum voltage of the input is 
the rail voltage, but one never feeds a voltage source directly to 2164.  
One drops the voltage across an input resistor (usual 30k) because the input pin 
is at virtual ground.  Hence, assuming a +15V supply, the largest current 
the input pin ever sees is about 500uA.  If the rail is connected directly 
to the input pin, who knows what the input current is -- possibly enough to fry 
the chip, I guess.  </font></span></div><span class="">
<div dir="ltr" align="left"><span class="m_4864580003579947465857172704-27062017"><font color="#0000ff" size="2" face="Arial"></font></span> </div>
<div dir="ltr" align="left">
<hr>
</div>
<div dir="ltr" align="left"><font size="2" face="Tahoma"><b>From:</b> Synth-diy 
[mailto:<a href="mailto:synth-diy-bounces@synth-diy.org" target="_blank">synth-diy-bounces@<wbr>synth-diy.org</a>] <b>On Behalf Of </b>Sean 
Ellis<br><b>Sent:</b> Monday, June 26, 2017 6:48 PM<br><b>To:</b> 
<a href="mailto:synth-diy@synth-diy.org" target="_blank">synth-diy@synth-diy.org</a><br><b>Subject:</b> [sdiy] 2164 overvoltage 
condition?<br></font><br></div>
</span><span class=""><blockquote style="BORDER-LEFT:#0000ff 2px solid;PADDING-LEFT:5px;MARGIN-LEFT:5px;MARGIN-RIGHT:0px" dir="ltr">
  <div></div>
  <div style="FONT-FAMILY:Calibri,Helvetica,sans-serif;COLOR:#000000;FONT-SIZE:12pt" dir="ltr" id="m_4864580003579947465divtagdefaultwrapper">
  <p>I've been breadboarding a filter and oscillator using a single 2164 and I 
  think I just fried my only 2164 on hand. I have the power supply protected but 
  accidentally put -12 straight into the input of one amp (the control pin was 
  at about 2.5V) and suddenly it died. The datasheet specifies the max ratings 
  to the supply rails so I don't get why it could have (seemingly) destroyed the 
  chip. Could it maybe have caused excessive heat?</p>
  <p><br></p>
  <p>-Sean<br></p></div></blockquote></span></div>
<br>______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br>
<br></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature" data-smartmail="gmail_signature">Quincas Moreira<br>Test Pilot at VBrazil Modular</div>
</div>