<div>One can abuse boost converter as inverter by adding negative peak detector (not sure if that's proper term). A capacitor and 2 diodes driven by coil's ramp voltage.<br></div><div><br></div><div>Roman<br></div><div class="nh_extra"><p>Dnia 9 maja 2017 23:24 Guy McCusker <guy.mccusker@gmail.com> napisał(a):<br></p><blockquote class="nh_quote" style="border-left: 2px solid #999; padding-left: 8px; margin: 0;"><div id="gwp125a4f62"><div>Can the LM25575 be used for 12V -> -15V ? The datasheet says that OUT<br></div><div>to GND is limited to Vin. That's why I guessed that it used the 15V<br></div><div>from the other converter as its input.<br></div><div><br></div><div>I didn't think about using the PCB layer as a heatsink though -- I am<br></div><div>a total novice at this! -- so that's a bit of very helpful insight.<br></div><div><br></div><div>On Tue, May 9, 2017 at 10:04 PM, Roman <modular@go2.pl> wrote:<br></div><blockquote is-minimized=""><div>My guess is IC2 (LM27313) is used for +12 -> +15V conversion. IC3 (LM25575)<br></div><div>is used as boost/inverter +12V -> -15V.<br></div><div>Obviously IC1 (LM2575) is for 5V.<br></div><div><br></div><div>If I was Roman F. I'd utilize most of the bottom layer as heatsink,<br></div><div>especially that IC1 and IC3 have exposed pads made just for that. IC2 (+15V)<br></div><div>has pretty good efficiency when supplied from 12V, about 90% according to<br></div><div>datasheet, so might be just slightly warm using only a bit of top layer<br></div><div>copper around it as heatsink.<br></div><div><br></div><div>Roman<br></div><div><br></div><div>Dnia 9 maja 2017 17:36 Guy McCusker <guy.mccusker@gmail.com> napisał(a):<br></div><div><br></div><div>Roman Filippov is selling PCBs for a power supply which he says is<br></div><div>enough for a Music Easel or 8 of his Buchla clone modules:<br></div><div><a href="https://electricmusicstore.com/products/power-supply-unit-model-211" nh-safe-redirect="" data-saferedirecturl="https://zasobygwp.pl/redirect?sig=cc5730914e631515fe1386040680101d39a8abe079279861724f808deb08b262&url=aHR0cHM6Ly9lbGVjdHJpY211c2ljc3RvcmUuY29tL3Byb2R1Y3RzL3Bvd2VyLXN1cHBseS11bml0LW1vZGVsLTIxMQ==" target="_blank">https://electricmusicstore.com/products/power-supply-unit-model-211</a><br></div><div><br></div><div>The board takes 12VDC input and produces +/-15V, +12V and +5V. Taking<br></div><div>a look at the BOM, I can see a 5V switching regulator, a boost<br></div><div>converter and a buck converter.<br></div><div><br></div><div>Presumably the 12V input is passed straight to the output, and the 5V<br></div><div>regulator does the obvious thing. For the +/-15V, do you think it<br></div><div>likely that he's using the boost to produce +15V, and then using the<br></div><div>buck converter to produce an inverted version of that for the -15v?<br></div><div><br></div><div>If so, then could someone check my reasoning and calculations for the<br></div><div>maximum current one could get out of this please? I am thinking this:<br></div><div><br></div><div>the boost converter has a thermal resistance of 166 deg/W. I see no<br></div><div>heatsinking and at 25C ambient and max operating temperature of 125 we<br></div><div>have about 100 degrees to play with, so can afford to dissipate 0.6W.<br></div><div><br></div><div>The device is up to 90% efficient, so that would mean we could get<br></div><div>5.4W out of it, dissipating the other 0.6W. So it can produce<br></div><div>something like 360mA of current, and this has to feed both the +15V<br></div><div>and -15V rails. You get a bit less because of the inefficiency of the<br></div><div>buck converter for the negative rail, so we're looking at about 150mA<br></div><div>per rail.<br></div><div><br></div><div>This does not seem enough. On the other hand I don't exactly know what<br></div><div>I am talking about here. Have I messed this up?<br></div><div><br></div><div>Cheers,<br></div><div>Guy.<br></div><div>_______________________________________________<br></div><div>Synth-diy mailing list<br></div><div><a nh-compose-link="" href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br></div><div><a href="http://synth-diy.org/mailman/listinfo/synth-diy" nh-safe-redirect="" data-saferedirecturl="https://zasobygwp.pl/redirect?sig=b71c8251b717ba551dbce4e296c1ab7f5c1f2f55b0f607f673fe803609e81823&url=aHR0cDovL3N5bnRoLWRpeS5vcmcvbWFpbG1hbi9saXN0aW5mby9zeW50aC1kaXk=" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br></div><div><br></div><div><br></div></blockquote><div><br></div><div>_______________________________________________<br></div><div>Synth-diy mailing list<br></div><div><a nh-compose-link="" href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br></div><div><a href="http://synth-diy.org/mailman/listinfo/synth-diy" nh-safe-redirect="" data-saferedirecturl="https://zasobygwp.pl/redirect?sig=b71c8251b717ba551dbce4e296c1ab7f5c1f2f55b0f607f673fe803609e81823&url=aHR0cDovL3N5bnRoLWRpeS5vcmcvbWFpbG1hbi9saXN0aW5mby9zeW50aC1kaXk=" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br></div></div></blockquote></div><div><br></div>