<div dir="ltr">Thanks Roman,<div><br></div><div>Tiny Speaker Test (tm) says that the voltage is indeed dropping off as it should in this case.</div><div><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Apr 4, 2017 at 3:09 PM, Roman <span dir="ltr"><<a href="mailto:modular@go2.pl" target="_blank">modular@go2.pl</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div>If it's square wave, DC meter will read half of amplitude, as it's just average value.<br></div><div>This is also RMS value so if your meter shows less in AC range, it's probably a model measuring average value and adjusting it for sine crest factor.<br></div><div>And if you see the same value before and after the filter, it may be because corner frequency of that filter is higher than input frequency.<br></div><div>BTW, checking how that circuit works would be way better with a speaker than voltmeter. Or at least oscilloscope. You're after interesting sonic values and not numbers on DVM, right? Build a filter that sounds good to you and then recalculate its values for all 96 frequencies.<span class="HOEnZb"><font color="#888888"><br></font></span></div><span class="HOEnZb"><font color="#888888"><div><br></div><div>Roman<br></div></font></span><div class="HOEnZb"><div class="h5"><div class="m_-9209971529157620763nh_extra"><p>Dnia 4 kwietnia 2017 21:34 Elain Klopke <<a href="mailto:functionofform@gmail.com" target="_blank">functionofform@gmail.com</a>> napisał(a):<br></p><blockquote class="m_-9209971529157620763nh_quote" style="border-left:2px solid #999;padding-left:8px;margin:0"><div id="m_-9209971529157620763gwp4fed1de5"><div id="m_-9209971529157620763gwp4fed1de5h"><div class="m_-9209971529157620763gwp4fed1de5b"><div dir="ltr"><div>I'm measuring in DC.<br></div><div><br></div><div>Measuring in AC gives me 2.03 volts at the source pin, before and after all the resistors.<br></div><div><br></div><div>connecting the resistor to the positive supply and measuring in DC gives me a reading of 5.06 V as if it was a plain bit of wire.<br></div><div><br></div><div>this is baffling because I checked the resistor with the resistance function again and it measures fine.... I even switched to the Hz function and measured the output square waves from the chip and got the expected frequencies.<br></div></div><div class="m_-9209971529157620763gwp4fed1de5_gmail_extra"><div><br></div><div class="m_-9209971529157620763gwp4fed1de5_gmail_quote"><div>On Tue, Apr 4, 2017 at 2:00 PM, Byron G. Jacquot <span dir="ltr"><<a href="mailto:thescum@surfree.com" target="_blank"></a><a href="mailto:thescum@surfree.com" target="_blank">thescum@surfree.com</a>></span> wrote:<br></div><blockquote class="m_-9209971529157620763gwp4fed1de5_gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div><div style="font-size:13px;color:rgb(0,0,0);font-family:arial,sans-serif"><div>Are you measuring AC or DC volts?<br></div><div><br></div><div><div>2.4VDC might be an OK reading for a 5VAC square wave, depending on how your meter integrates it.<br></div><span><div><br></div><div><br></div><div><blockquote style="padding-left:5px;margin-left:0px;border-left:#0000ff 2px solid;font-weight:normal;font-style:normal;text-decoration:none;font-size:10pt;font-family:arial,sans-serif;color:black"><div>-----Original Message----- <br></div><div>From: Elain Klopke <u></u> <br></div><div>Sent: Apr 4, 2017 12:43 PM <br></div><div>To: *SYNTH DIY <u></u> <br></div><div>Subject: [sdiy] breadboard woes <br></div><div><br></div><div dir="ltr"><div>So I was trying to get a reading on my breadboard to see how much voltage was lost between the input of three passive low pass filters in series and the output. <br></div><div><br></div><div>My measurements between ground and:<br></div><div>positive supply: 5.06 V<br></div><div>Output from chip: 2.4 V (was expecting 5 V because digital square wave)<br></div><div>junction of first and second resistor: 2.4 V<br></div><div>junction between second and third resistor: 2.4 V<br></div><div>after third resistor: 2.4 V ....<br></div><div><br></div><div>All resistors measured at 5.07 kOhms. I'm not sure what's going on. Is my breadboard messed up somehow or am I missing something fundamental about electronics?<br></div></div><div><u></u><u></u><br></div></blockquote></div></span></div></div></div><div><br></div><div>______________________________<wbr>_________________<br></div><div> Synth-diy mailing list<br></div><div> <a href="mailto:Synth-diy@synth-diy.org" target="_blank"></a><a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br></div><div> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br></div><div> <br></div></blockquote></div></div></div></div></div><div id="m_-9209971529157620763gwpebfa16e9"><div>______________________________<wbr>_________________<br></div><div>Synth-diy mailing list<br></div><div><a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br></div><div><a href="http://synth-diy.org/mailman/listinfo/synth-diy" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br></div></div></blockquote></div><div><br></div></div></div></blockquote></div><br></div>