<p dir="ltr">Thanks, I'll check out that flux.</p>
<p dir="ltr">So you don't use any flux for the smaller parts? Does that work well at all?</p>
<br><div class="gmail_quote"><div dir="ltr">On Thu, 23 Mar 2017 17:31 Vladimir Pantelic, <<a href="mailto:vladoman@gmail.com">vladoman@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">congrats of going SMD, but I have to say I find your technique overly<br class="gmail_msg">
complex.<br class="gmail_msg">
<br class="gmail_msg">
what I do for 0603/0805 and SOT/SO parts:<br class="gmail_msg">
<br class="gmail_msg">
1) apply solder (0.35mm, lead free Felder ISOCORE, 3.5% flux, no clean)<br class="gmail_msg">
to one pad, or diagonal pads if a larger IC<br class="gmail_msg">
<br class="gmail_msg">
2) pick part with tweezers, reheat the pad with the solder and place the<br class="gmail_msg">
part<br class="gmail_msg">
<br class="gmail_msg">
3) solder the other pad(s)<br class="gmail_msg">
<br class="gmail_msg">
4) done.<br class="gmail_msg">
<br class="gmail_msg">
for smaller ICs like TSSOP I add some Edsyn FL22 flux to the pads, then<br class="gmail_msg">
solder them with the same 0.35mm solder and tip as above, using a $200<br class="gmail_msg">
stereo microscope (Amscope SE 400-Z, 10X)<br class="gmail_msg">
<br class="gmail_msg">
<br class="gmail_msg">
<br class="gmail_msg">
On 23.03.2017 09:00, cheater00 cheater00 wrote:<br class="gmail_msg">
> Hi,<br class="gmail_msg">
> I have recently bought an SMD learning kit to try out some techniques.<br class="gmail_msg">
> I've had some really good results that were stunning for a person who<br class="gmail_msg">
> tried real SMD soldering for the first time, so I thought I'd share<br class="gmail_msg">
> what I did and what I used.<br class="gmail_msg">
><br class="gmail_msg">
> I got one that looks like this, but I think I got mine on Amazon:<br class="gmail_msg">
><br class="gmail_msg">
> <a href="https://www.aliexpress.com/item/DIYmall-SMT-SMD-Component-Welding-Practice-Board-Soldering-DIY-Kit-Resitor-Diode-Transistor-By-start-Learning/32776255634.html" rel="noreferrer" class="gmail_msg" target="_blank">https://www.aliexpress.com/item/DIYmall-SMT-SMD-Component-Welding-Practice-Board-Soldering-DIY-Kit-Resitor-Diode-Transistor-By-start-Learning/32776255634.html</a><br class="gmail_msg">
><br class="gmail_msg">
> The 1206 were easy, as were the 0805 and 0603. Too bad they didn't<br class="gmail_msg">
> have smaller ones. I didn't have to use a microscope but I wear<br class="gmail_msg">
> contact lenses so my vision is OK. Good lighting was crucial (see by<br class="gmail_msg">
> the end of the email), as my eyes couldn't resolve the detail without<br class="gmail_msg">
> it. With the light the work was really comfortable.<br class="gmail_msg">
><br class="gmail_msg">
> I've used my Hakko-clone soldering station Aoyue Int2903 with this<br class="gmail_msg">
> Hakko-clone T12 tip type JL-02:<br class="gmail_msg">
><br class="gmail_msg">
> <a href="https://www.aliexpress.com/store/product/Hot-Hakko-T12-Soldering-Tips-T12-JL02-Series-Iron-Solder-Tip-For-Hakko-Fx-951-high/1486111_32574864414.html" rel="noreferrer" class="gmail_msg" target="_blank">https://www.aliexpress.com/store/product/Hot-Hakko-T12-Soldering-Tips-T12-JL02-Series-Iron-Solder-Tip-For-Hakko-Fx-951-high/1486111_32574864414.html</a><br class="gmail_msg">
><br class="gmail_msg">
> The tip I used worked pretty good.<br class="gmail_msg">
><br class="gmail_msg">
> I used AmTech Tacky Flux, model NC-559-V2-TF. I bought it from Insat<br class="gmail_msg">
> on <a href="http://www.bga-reworking.co.uk/" rel="noreferrer" class="gmail_msg" target="_blank">http://www.bga-reworking.co.uk/</a>. They have other good soldering<br class="gmail_msg">
> stuff so check them out. I made enough of an order that they sent me a<br class="gmail_msg">
> set of tweezers and cutters. The tweezers are ESD and very precise,<br class="gmail_msg">
> the cutters have really nice blades but the spring shifts around which<br class="gmail_msg">
> is annoying.<br class="gmail_msg">
><br class="gmail_msg">
> It's important to buy the flux from an authorized distributor listed<br class="gmail_msg">
> on this page:<br class="gmail_msg">
><br class="gmail_msg">
> <a href="http://www.inventecusa.com/reps---distributors.html" rel="noreferrer" class="gmail_msg" target="_blank">http://www.inventecusa.com/reps---distributors.html</a><br class="gmail_msg">
><br class="gmail_msg">
> You can find AmTech knockoffs nearly everywhere and obviously they're<br class="gmail_msg">
> not going to have the same chemical composition as the original.<br class="gmail_msg">
> Amazon has the knockoff, so does eBay. The flux is really important.<br class="gmail_msg">
><br class="gmail_msg">
> I first put the board in a "helping hand" stand, although I am<br class="gmail_msg">
> awaiting the delivery of an inexpensive pcb holder vise. Does anyone<br class="gmail_msg">
> know where to get aligator clips for the helping hand that don't have<br class="gmail_msg">
> the teeth? Much rather rubber jaws or no teeth at all? That would be<br class="gmail_msg">
> so much better. I might put some heat shrink on these.<br class="gmail_msg">
><br class="gmail_msg">
> I start soldering by applying a tiny amount of the flux to the board.<br class="gmail_msg">
> Then I'd add some Stannol SN60Pb39Cu1 to the pads. I have a 1.00mm<br class="gmail_msg">
> diameter 500g spool that'll last me, my children, and my children's<br class="gmail_msg">
> children a lifetime. I could use some finer solder though, maybe<br class="gmail_msg">
> 0.2mm, because 1mm really applies very quickly. I'm holding my<br class="gmail_msg">
> soldering iron in my right hand.<br class="gmail_msg">
><br class="gmail_msg">
> Next I'll take a pair of ESD tweezers and, holding the tape in my<br class="gmail_msg">
> right hand, I'll pry it open with the tweezers and pick out the part.<br class="gmail_msg">
> I'll put it on the board and apply heat to the top pad with the<br class="gmail_msg">
> soldering iron, then to the other pad. The part will not have settled<br class="gmail_msg">
> yet, so once it's held securely by the joints I'll let go with the<br class="gmail_msg">
> tweezer and heat both pads alternating between them until the part<br class="gmail_msg">
> settles. If it needs pushing in place I'll use the tweezer or a<br class="gmail_msg">
> spudger. I'm going to buy a magnetic knife holder thing for my<br class="gmail_msg">
> tweezers and spudgers which should make the process easier.<br class="gmail_msg">
><br class="gmail_msg">
> At this point the resistor pads will have gratuitous balls of solder<br class="gmail_msg">
> on them, so I'll remove nearly all of it with Pollin 1mm wick, order #<br class="gmail_msg">
> 840 030:<br class="gmail_msg">
><br class="gmail_msg">
> <a href="http://www.pollin.de/shop/dt/OTY5OTUxOTk-/Werkstatt/Loettechnik/Entloetgeraete/Entloetlitze_1_0_mm_1_5_m.html" rel="noreferrer" class="gmail_msg" target="_blank">http://www.pollin.de/shop/dt/OTY5OTUxOTk-/Werkstatt/Loettechnik/Entloetgeraete/Entloetlitze_1_0_mm_1_5_m.html</a><br class="gmail_msg">
><br class="gmail_msg">
> it comes out of the spool condensed so I twist it around until it<br class="gmail_msg">
> separates into a mesh. This way it'll absorb much more solder for the<br class="gmail_msg">
> same length.<br class="gmail_msg">
><br class="gmail_msg">
> At this point I might have to realign the resistor so I'll use some<br class="gmail_msg">
> heat and a spudger. I use these spudgers:<br class="gmail_msg">
><br class="gmail_msg">
> <a href="https://www.aliexpress.com/item/6Pcs-Hand-Tool-Professional-Steel-Solder-Assist-Electronic-Components-Repair-Welding-Auxiliary-Tools-Set-FULI/32780051115.html" rel="noreferrer" class="gmail_msg" target="_blank">https://www.aliexpress.com/item/6Pcs-Hand-Tool-Professional-Steel-Solder-Assist-Electronic-Components-Repair-Welding-Auxiliary-Tools-Set-FULI/32780051115.html</a><br class="gmail_msg">
><br class="gmail_msg">
> or at least ones that look the same. I don't know where I bought them<br class="gmail_msg">
> any more. ("Welding" is Aliexpress for "Soldering" and "Auxiliary<br class="gmail_msg">
> tool" is for "accessory", useful when searching for something)<br class="gmail_msg">
><br class="gmail_msg">
> The flux makes all the difference. I did the first resistor with the<br class="gmail_msg">
> flux, and it worked well. I did the neighbouring one without applying<br class="gmail_msg">
> flux, I just used flux from the previous one, and that was pretty good<br class="gmail_msg">
> too. I tried the third pad watching out not to apply any flux, and the<br class="gmail_msg">
> results were really bad. As soon as I applied a little flux the joints<br class="gmail_msg">
> cleaned up, and the resistor applied well. The flux also smells really<br class="gmail_msg">
> nice. I later cleaned it off with some 70% ethanol and normal q-tips.<br class="gmail_msg">
><br class="gmail_msg">
> I don't have a good light set up yet so during the process I used the<br class="gmail_msg">
> Black Diamond Revolt head-mounted lamp which I bought several years<br class="gmail_msg">
> ago, use all the time, and it remains like new.<br class="gmail_msg">
><br class="gmail_msg">
> <a href="http://blackdiamondequipment.com/en_US/headlamps-and-lanterns/revolt-BD620613_cfg.html" rel="noreferrer" class="gmail_msg" target="_blank">http://blackdiamondequipment.com/en_US/headlamps-and-lanterns/revolt-BD620613_cfg.html</a><br class="gmail_msg">
><br class="gmail_msg">
> It has an adjustable angle mount which was very important for soldering.<br class="gmail_msg">
><br class="gmail_msg">
> The nice thing about this soldering technique is that it gave me<br class="gmail_msg">
> really perfect results without much of a fight. I might still have to<br class="gmail_msg">
> practice to leave more solder on the pads, but the initial results are<br class="gmail_msg">
> very promising.<br class="gmail_msg">
><br class="gmail_msg">
> The one improvement I'd like is a different tweezer. A sideways<br class="gmail_msg">
> tweezer would be better, where the jaws curve in on themselves out of<br class="gmail_msg">
> the plane of the sheet metal the tweezer is made of. I haven't been<br class="gmail_msg">
> able to find one with a nice angle (say 75 degrees) and a fine tip and<br class="gmail_msg">
> ESD coating. If anyone has a suggestion, I'd love to hear about it.<br class="gmail_msg">
><br class="gmail_msg">
> After cleaning with 70% ethanol, the board still seems to have a bit<br class="gmail_msg">
> of a film on it, so if someone has a suggestion for a better solvent<br class="gmail_msg">
> for the AmTek flux, let me know please.<br class="gmail_msg">
><br class="gmail_msg">
> Hope this helps someone. If not, at least I had fun documenting what I<br class="gmail_msg">
> did in case I forget in the future :)<br class="gmail_msg">
> _______________________________________________<br class="gmail_msg">
> Synth-diy mailing list<br class="gmail_msg">
> <a href="mailto:Synth-diy@synth-diy.org" class="gmail_msg" target="_blank">Synth-diy@synth-diy.org</a><br class="gmail_msg">
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" class="gmail_msg" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br class="gmail_msg">
><br class="gmail_msg">
<br class="gmail_msg">
_______________________________________________<br class="gmail_msg">
Synth-diy mailing list<br class="gmail_msg">
<a href="mailto:Synth-diy@synth-diy.org" class="gmail_msg" target="_blank">Synth-diy@synth-diy.org</a><br class="gmail_msg">
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" class="gmail_msg" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br class="gmail_msg">
</blockquote></div>