<div dir="ltr">The dual transformer Rutger mention's is exactly what I've been looking for lately and should work for us ... I need something with at least 2 secondaries that will go down to a 5v rail and a single 15v rail. I only spent some time last night looking but I'm digging these Bel MT series transformers that are designed for a 5v and +/-15 or 12v supplies. <div><br></div><div>this one is smaller, check the datasheet for more powerful options: </div><div><a href="http://www.mouser.com/ProductDetail/Bel-Signal-Transformer/MT-6-15/?qs=0%2F2GmT7MRM%252bQI%252bgfp3ZvBQ%3D%3D">http://www.mouser.com/ProductDetail/Bel-Signal-Transformer/MT-6-15/?qs=0%2F2GmT7MRM%252bQI%252bgfp3ZvBQ%3D%3D</a><br></div><div><br></div><div>In our case we would only need to use half of the secondary with CT. If anyone knows a source of similar transformers where theres no center tap I'd love to see.</div><div><br></div><div>Best,</div><div><br></div><div>N</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Mar 7, 2017 at 7:27 AM, Rutger Vlek <span dir="ltr"><<a href="mailto:rutgervlek@gmail.com" target="_blank">rutgervlek@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div>Good point Ingo!</div><div><br></div><div>Towards the end of the service manual (<a href="http://www.vintageshifi.com/repertoire-pdf/pdf/telecharge.php?pdf=Yamaha-A-3-Service-Manual.pdf" target="_blank">http://www.vintageshifi.com/<wbr>repertoire-pdf/pdf/telecharge.<wbr>php?pdf=Yamaha-A-3-Service-<wbr>Manual.pdf</a>) the PSU schematic is displayed. There's a full PSU diagram, and an overview diagram. The latter shows a straight coupling between both DC grounds of the 12V and 6V lines, however the first diagram does not! Confusing, I'll measure this in the actual unit to be sure.</div><div><br></div><div>Assuming both grounds are connected, what you wrote is applicable here. So it means I'll have to start looking for a transformer with dual independent secondaries for 6.3V and 13V (or 12.6V). Anyone knows one? At least 7VA total.</div><div><br></div><div>Regards,</div><div><br></div><div>Rutger</div><div><div class="h5"><div><br></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Mar 6, 2017 at 6:06 PM, Ingo Debus <span dir="ltr"><<a href="mailto:igg.debus@gmail.com" target="_blank">igg.debus@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;padding-left:1ex;border-left-color:rgb(204,204,204);border-left-width:1px;border-left-style:solid"><br>
> Am 06.03.2017 um 14:00 schrieb Roman Sowa <<a href="mailto:modular@go2.pl" target="_blank">modular@go2.pl</a>>:<br>
><br>
>><br>
>> Is there any harm in using the centre tap for the 6.3V and the end taps<br>
>> for the 12.6V supply to the PSU? It means the coil between one end and<br>
>> centre tap gets a little more loading than the other side. The same<br>
><br>
> No problem at all, just make sure that added load from 6V and 12V circuits doesn't exceed current rating for that winding.<br>
<br>
Careful. This won’t work if the two secondary windings of the original transformer are isolated from each other, and they are feeding two bridge rectifiers, and on the DC side of the bridge rectifiers the grounds are connected.<br>
<br>
With two half-wave rectifiers there’ll be no problem however.<br>
<br>
Ingo<br>
______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br>
</blockquote></div><br></div></div></div></div>
<br>______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br>
<br></blockquote></div><br></div>