<div dir="ltr">I'm not a euro mfg so take this all with grain of salt.<br><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Jan 3, 2017 at 2:35 PM, Jacob Watters <span dir="ltr"><<a href="mailto:jacobwatters@gmail.com" target="_blank">jacobwatters@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">Thanks for all of the feedback so far. Here are my notes:<div><br></div><div>Boxed Header</div><div>This is what I plan to use. Maybe my pin umbers are off. I was going by the image linked below. Is pin 1 on the bottom right in this image?</div><div><br></div><div><a href="http://www.doepfer.de/a100_man/a100b_e.gif" target="_blank">http://www.doepfer.de/a100_man<wbr>/a100b_e.gif</a></div></div></blockquote><div><br></div><div>pin1 is not labeled in that image. this gets to the heart of all the red stripe problems.</div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><br></div><div><br></div><div>Diode</div><div>It seems like I should just not use it?</div></div></blockquote><div><br></div><div>diodes are always a good idea where it's possible to connect power incorrectly.</div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><br></div><div>Resistor</div><div>Don't use it?</div></div></blockquote><div><br></div><div>It doesn't hurt anything, and it's nice to have series elements on power inputs to experiment with in case you determine filtering is needed, or for current measurements.</div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><br></div><div>Ferrite Bead</div><div>Some people are telling me outside this list that ferrite is more for digital stuff and that the capacitor should be fine. If I don't use the ferrite then should I use a resistor instead?</div></div></blockquote><div><br></div><div>If you determine you need a ferrite, you can put it in the spot that resistor above was using, otherwise don't worry about it.</div><div><br></div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><br></div><div>Capacitors</div><div>Only use the larger one (I use a 0.1uF bypass cap at each IC anyway). Some say increase and some say decrease. In non-modular stuff I usually use larger ones, so I am leaning towards 22uF.</div></div></blockquote><div><br></div><div>Caps at power entry are "bulk" caps and their value isn't critical as long as they are large. What is "large" would be relative to the inductance seen on the ribbon cable, bus board, etc and the instantaneous current draw of the module as a whole,  but would probably be something like 10uF or 22uF or higher.</div><div><br></div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><br></div><div><br></div><div>I wish that there was a standard for this so I knew what to do :(</div></div></blockquote><div><br></div><div>No standard required. Just pick a reasonable worst case scenario and design/test to that (easier said than done I know).</div><div><br></div><div>mh</div><div> <br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><br></div></div><div class="m_371130383879298354HOEnZb"><div class="m_371130383879298354h5"><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Jan 3, 2017 at 4:52 PM, Andre Majorel <span dir="ltr"><<a href="mailto:aym-htnys@teaser.fr" target="_blank">aym-htnys@teaser.fr</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><span>On 2017-01-03 12:56 -0800, Tim Ressel wrote:<br>
<br>
> I found a 22uF bulk cap is the minimum for noise reduction.<br>
> Remember the rails in Eurorack case can be noisy. 10 ohms is<br>
> okay for a module that pulls little current. I use 1 ohm.<br>
<br>
</span>Some years ago, Tony Allgood mentioned that he had to switch<br>
from 22 to 2.2 µF per rail because the surge current from lots<br>
of 22 µF capacitors in parallel made certain Power-one supplies<br>
misbehave on power-up. But that was with ferrite beads, not<br>
resistors.<br>
<span class="m_371130383879298354m_-7459890223306720180HOEnZb"><font color="#888888"><br>
--<br>
André Majorel <a href="http://www.teaser.fr/~amajorel/" rel="noreferrer" target="_blank">http://www.teaser.fr/~amajorel<wbr>/</a><br>
</font></span><div class="m_371130383879298354m_-7459890223306720180HOEnZb"><div class="m_371130383879298354m_-7459890223306720180h5">______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br>
</div></div></blockquote></div><br></div>
</div></div><br>______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br>
<br></blockquote></div><br></div></div>