<div>That's what I've been looking for! Thank you!<br></div><div>I was almost ready to machine those myself...<br></div><div>Although I'd rather have one for 1/8'' shaft or 4mm, have you seen them anywhere?<br></div><div><br></div><div>Roman<br></div><div class="nh_extra"><p>Dnia 29 listopada 2016 21:24 Matthias Herrmann <matthias.herrmann@fonik.de> napisał(a):<br></p><blockquote class="nh_quote" style="border-left: 2px solid #999; padding-left: 8px; margin: 0;"><div id="gwp63be9340"><div id="gwp63be9340h"><div link="blue" vlink="purple" class="gwp63be9340b" data-message-body="true" lang="DE"><div class="gwp63be9340_Section1"><p class="gwp63be9340_MsoNormal"><span class="colour" style="color:rgb(31, 73, 125)"><span class="font" style="font-family:"Calibri","sans-serif""><span class="size" style="font-size:11pt">Anybody used axle bushings like these? they should keep some stress
from the encoder:<br> http://www.reichelt.de/Potiknoepfe/P6-SCREW-ACHSE/3/index.html?ACTION=3&LA=2&ARTICLE=42129&GROUPID=3139&artnr=P6+SCREW+ACHSE&SEARCH=%252A</span></span></span></p><p class="gwp63be9340_MsoNormal"><span class="colour" style="color:rgb(31, 73, 125)"><span class="font" style="font-family:"Calibri","sans-serif""><span class="size" style="font-size:11pt"> </span></span></span><br></p><p class="gwp63be9340_MsoNormal"><span class="colour" style="color:rgb(31, 73, 125)"><span class="font" style="font-family:"Calibri","sans-serif""><span class="size" style="font-size:11pt"> </span></span></span><br></p><div style="border:none;border-left:solid blue 1.5pt;padding:0cm 0cm 0cm 4.0pt"><div><div style="border:none;border-top:solid #B5C4DF 1.0pt;padding:3.0pt 0cm 0cm 0cm"><p class="gwp63be9340_MsoNormal"><b><span class="font" style="font-family:"Tahoma","sans-serif""><span class="size" style="font-size:10pt">Von:</span></span></b><span class="font" style="font-family:"Tahoma","sans-serif""><span class="size" style="font-size:10pt">Synth-diy
[mailto:synth-diy-bounces@synth-diy.org] <b>Im Auftrag von </b>Jean-Pierre
Desrochers<br> <b>Gesendet:</b> Dienstag, 29. November 2016 21:00<br> <b>An:</b> Tom Wiltshire<br> <b>Cc:</b>synth-diy@synth-diy.org<br> <b>Betreff:</b> Re: [sdiy] Incremental encoder to up / down counter or pots and
an ADC</span></span></p></div></div><p class="gwp63be9340_MsoNormal"> <br></p><p><span class="font" style="font-family:"Verdana","sans-serif""><span class="size" style="font-size:10pt">Hi Tom,</span></span><br></p><pre>> A non-threaded shaft is never going to be tight in the first place, is it?<br></pre><pre><div>> <u>As long as the hole that that the encoder goes through is a nice tight fit</u>..<br></div><div>
<br></div><div>
That's exactly the problem with MANY cheapo mixers that have too large holes<br></div></pre><pre>for the pot's shaft and these shafts are rocked in all the way<br></pre><pre>with no secure mecanical provision.. Even with a brand new console<br></pre><pre>you can 'feel' the loose the shafts have in their non supporting holes.<br></pre><pre>Sometimes companies like Fender (to name one) use small plastic<br></pre><pre>washers to fill the holes circular gaps for tightening the shafts in place.<br></pre><pre>These pots or encoders are too often used with too much of their shaft<br></pre><pre>going outside the metal front panel causing the premature mecanical<br></pre><pre>degradation. Try to imagine.. when you need to pull their knobs for repair<br></pre><pre>you fear of ripping these shaft out of the device..<br></pre><p><span class="font" style="font-family:"Verdana","sans-serif""><span class="size" style="font-size:10pt"><br>JP</span></span></p><p><span class="font" style="font-family:"Verdana","sans-serif""><span class="size" style="font-size:10pt"> </span></span><br></p><p><span class="font" style="font-family:"Verdana","sans-serif""><span class="size" style="font-size:10pt">Le
2016-11-29 14:09, Tom Wiltshire a écrit :</span></span><br></p><blockquote is-minimized="" style="border:none;border-left:solid #1010FF 1.5pt;padding:0cm 0cm 0cm 4.0pt; margin-left:3.75pt;margin-top:5.0pt;margin-bottom:5.0pt"><pre>+1 agree. This is a classic microcontroller job.<br></pre><pre> <br></pre><pre>JP, what do you mean that these non-threaded shafts "get loose over time"? A non-threaded shaft is never going to be tight in the first place, is it? As long as the hole that that the encoder goes through is a nice tight fit, I don't see a particular problem (assuming the PCB is well supported). So what am I missing?<br></pre><pre> <br></pre><pre>Thanks,<br></pre><pre>Tom<br></pre><pre> <br></pre><pre> <br></pre></blockquote><div><pre> <br></pre></div></div></div></div></div></div><div id="gwp2dc0e7e6"><div>_______________________________________________<br></div><div>Synth-diy mailing list<br></div><div><a nh-compose-link="" href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br></div><div><a href="http://synth-diy.org/mailman/listinfo/synth-diy" nh-safe-redirect="" data-saferedirecturl="https://zasobygwp.pl/redirect?sig=b71c8251b717ba551dbce4e296c1ab7f5c1f2f55b0f607f673fe803609e81823&url=aHR0cDovL3N5bnRoLWRpeS5vcmcvbWFpbG1hbi9saXN0aW5mby9zeW50aC1kaXk=" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br></div></div></blockquote></div><div><br></div>