<div dir="ltr">And to clarify some on that too: nobody says the sleeve ground has to be connected to the DIN ground.....</div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Aug 25, 2016 at 5:04 AM, Paul Burns <span dir="ltr"><<a href="mailto:paul@pbdj.co.uk" target="_blank">paul@pbdj.co.uk</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><u></u>
<div><p>When Mutable Instruments first brought out the Grids Module , the first thing I did was make the smallest possble Midi converter I could using a stereo 3.5mm jack...left, right, ground. Works just fine. Hid it all behind a 4 HP panel. Cable has TRS 3.5mm one end , 5 pin din the other.<br></p><p><br></p><p>regards<span class="HOEnZb"><font color="#888888"><br></font></span></p><span class="HOEnZb"><font color="#888888"><p><br></p><p>Paul<br></p></font></span><div><div class="h5"><p><br></p><p><br></p><p><br></p><blockquote type="cite"><p>On 25 August 2016 at 07:59 ASSI <<a href="mailto:Stromeko@nexgo.de" target="_blank">Stromeko@nexgo.de</a>> wrote:<br><br><br>On Wednesday, 24 August 2016 15:27:38 CEST <a href="mailto:rsdio@audiobanshee.com" target="_blank">rsdio@audiobanshee.com</a> wrote:</p><blockquote type="cite"><p>mini-DIN receptacles are still a lot larger than low-profile 3.5mm jacks.</p></blockquote><p>The standard board profile for through-hole about 13mm on all sides, <br>Switchcraft 3.5mm board mount is 12x12x5mm³. Panel mountable hardware <br>requires about 14x25x10mm³ (fastened with two screws), Kycon 3.5mm panel mount <br>is roughly 10mm on all sides. There are smaller miniDIN variants that are <br>fastened with only a single screw or snap-in to the panel, but I'd avoid the <br>latter at least for DIY.<br><br>So in theory you might get two 3.5mm jacks panel mounted to the same space <br>where one mini-DIN goes, but your users would curse you for it. Any other way <br>it's a wash from where I sit. Plus mini-DIN has dual receptables for doing <br>MIDI In / Out readily available (even color-coded for mouse/keyboard).<br></p><blockquote type="cite"><p>If<br>you're going to have a MIDI connector that isn't standard, then you might<br>as well use the smallest components. MIDI is quite forgiving of cheap<br>cables and connectors, so long as they don't completely fail.</p></blockquote><p>Other equipment using the 3.5mm jack for audio might not be so forgiving.<br><br>Say you wanted _larger_ MIDI plugs because you expect klutzy users… just <br>because CEE plugs are large and have five pins doesn't mean it's be a good <br>idea to use them in this application.<br></p><blockquote type="cite"><p>A D-sub DA-15 could be wired like the old Soundblaster audio card, and that<br>would at least be compatible with some MIDI interfaces. Not sure whether it<br>would be slightly taller than a 3.5mm (certainly wider!).</p></blockquote><p>It would not only be taller than 3.5mm, but also slightly taller than mini-<br>DIN. If you're trying to go smaller, then using an RJ 6p6c (telephone) or <br>8p8c jack (ethernet) might be an option, but then you'll have to make your own <br>adapters. I still have a plan for a MIDI matrix that was supposed to use the <br>latter in order to fit into 1U in the rack.<br><br><br>Regards,<br>Achim.<br>-- <br>+<[Q+ Matrix-12 WAVE#46+305 Neuron microQkb Andromeda XTk Blofeld]>+<br><br>Samples for the Waldorf Blofeld:<br><a href="http://Synth.Stromeko.net/Downloads.html#BlofeldSamplesExtra" target="_blank">http://Synth.Stromeko.net/<wbr>Downloads.html#<wbr>BlofeldSamplesExtra</a><br><br>______________________________<wbr>_________________<br>Synth-diy mailing list<br><a href="mailto:Synth-diy@dropmix.xs4all.nl" target="_blank">Synth-diy@dropmix.xs4all.nl</a><br><a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" target="_blank">http://dropmix.xs4all.nl/<wbr>mailman/listinfo/synth-diy</a></p></blockquote></div></div></div>
<br>______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/<wbr>mailman/listinfo/synth-diy</a><br>
<br></blockquote></div><br></div>