<div dir="ltr">Regarding LS and plain-old-TTL compatibility: I think both are nominally compatible.  But LS fan-in and fan-out must be carefully considered due to the higher currents of plain-old-TTL compared to LS TTL.<div><br></div><div>JJS (old-timer who designed numerous TTL and ECL circuits after graduating from college)<br><div class="gmail_extra"><br><div class="gmail_quote">On Fri, Jun 3, 2016 at 5:40 PM, Michael E Caloroso <span dir="ltr"><<a href="mailto:mec.forumreader@gmail.com" target="_blank">mec.forumreader@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">The LS series are a direct replacement.  They just consume less power<br>
and are slightly faster.<br>
<br>
MC<br>
<br>
On 6/2/16, Jean-Pierre Desrochers <<a href="mailto:jpdesroc@oricom.ca">jpdesroc@oricom.ca</a>> wrote:<br>
> Looking at page 6 of this:<br>
> <a href="http://www.ti.com.cn/cn/lit/ds/symlink/sn74ls147.pdf" rel="noreferrer" target="_blank">http://www.ti.com.cn/cn/lit/ds/symlink/sn74ls147.pdf</a><br>
> I have my answer..<br>
> The LS family has higher input impedance thus for pullup resistors is<br>
> better here..<br>
><br>
><br>
> Le 2016-06-02 09:03, Jean-Pierre Desrochers a écrit :<br>
>> I am refurbishing a vintage 1976 ARP Pro Soloist and<br>
>> everything goes well so far.<br>
>> But when removing all socketed TTL IC's one after each other<br>
>> to 'clean' their pins before putting them back in their sockets<br>
>> I noticed one of them had 3 of its pins rusted down very badly and<br>
>> falling off..<br>
>> So I have to replace it.<br>
>><br>
>> Looking at the service manual:<br>
>> <a href="http://www.synthfool.com/docs/Arp/ARP_Pro_Soloist-Service_Manual.pdf" rel="noreferrer" target="_blank">http://www.synthfool.com/docs/Arp/ARP_Pro_Soloist-Service_Manual.pdf</a><br>
>> pages 54, 55 It's one of the 2 Priority Encoders 10 to 4 Line SN74148<br>
>> (Z1 & Z2).<br>
>><br>
>> These chips scan many of the presets rocker switches.<br>
>> My question is can I replace the original SN74148 for 74LS148 ?<br>
>> The former is very old and almost gone (unless bought at eBay).<br>
>> So far I found 5 x 74LS148 at a local electronic parts dealer<br>
>> and I think that they will do but I want to make sure with you guys.<br>
>> In the past I replaced many SN74xxx for 74LSxxx but these<br>
>> were in TTL to TTL connections boards.<br>
>> Here its input impedance issues (switches with pullups) I'm aware of..<br>
>><br>
>> Thanks.<br>
>> _______________________________________________<br>
>> Synth-diy mailing list<br>
>> <a href="mailto:Synth-diy@dropmix.xs4all.nl">Synth-diy@dropmix.xs4all.nl</a><br>
>> <a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
><br>
> --<br>
> « L'indépendance, c'est comme un pont :<br>
> avant, personne n'en veut, après, tout le monde le prend. »<br>
> Félix Leclerc<br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@dropmix.xs4all.nl">Synth-diy@dropmix.xs4all.nl</a><br>
> <a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
><br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
</blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature" data-smartmail="gmail_signature"><p><span style="font-family:"Courier New"">John Speth,
Software Engineer, Avnera</span></p></div>
</div></div></div>