<div dir="ltr">Also, if your lead with the cap soldered to the end you're using as a probe is only grounded at the connector end, this could erroneously be telling you that there is noise present when in fact there actually isn't. I'd recommend using a cheap scope probe instead, and grounding the probe end with the flying lead as close as possible to the signal you're actually probing. Years ago when I did a lot of audio design, I modded a hifi amplifier by adding a BNC socket to its front panel so I could plug a scope probe (or any other bit of my usual BNC plumbing) right into the amplifier so I could listen to what was going on rather than just see it on a scope.<div><br></div><div>On the subject of the power supply, it should work pretty well. It doesn't have any RF interference filtering, however, so that <i>could</i> be an issue if you're close to something that radiates significantly.</div><div><br></div><div>Sarah</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Feb 29, 2016 at 3:08 PM, Tom Bugs <span dir="ltr"><<a href="mailto:admin@bugbrand.co.uk" target="_blank">admin@bugbrand.co.uk</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">10u to 220u between V+ and 0V and between 0V and V- where power comes in (filter caps) - watch polarity, of course.<br>
100n between V+ and 0V and between 0V and V- as close to the power pins of each IC.<div class="HOEnZb"><div class="h5"><br>
<br>
On 29/02/2016 22:03, Joe wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Tom, No. As I stated I am strictly monkey see, monkey do. Trying to<br>
change that. I am going to get a book, now.  Ray Wilson's "Make: Analog<br>
Synthesizers" was recommended.<br>
  Can you tell me what to add where? Thanks.<br>
Joe.<br>
<br>
<br>
<br>
<br>
<br>
On Mon, 2016-02-29 at 21:34 +0000, Tom Bugs wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Question - do you have filter & bypass caps on the circuits? They're not<br>
shown in the original schematic.<br>
<br>
<br>
On 29/02/2016 17:06, Joe wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hello and thanks. My power supply is the bipolar power supply circuit<br>
provided by General Guitar Gadgets found here<br>
<a href="http://www.generalguitargadgets.com/wp-content/uploads/ggg_bipolar_ps.pdf" rel="noreferrer" target="_blank">http://www.generalguitargadgets.com/wp-content/uploads/ggg_bipolar_ps.pdf</a><br>
I have used it before but for other circuits that generate cv. There<br>
never seemed to be noticeable downstream noise in the audio in those<br>
circuits. Those circuits were the EFM pv-1 and an envelope circuit Harry<br>
Bissell sent me, also EFM I bet. I used 3080s in those, too. I find the<br>
same noise where the ground is connected from the bipolar power supply<br>
board to the panning vca board, by the way.<br>
   My audio probe is a 0.1uf cap on the tip of an audio cable with the<br>
audio cable shield connected to ground.<br>
   So, before I try to use a LM13700, is there some procedure I can use to<br>
determine the noise source. Removing ICs and powering up or something<br>
like that?<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
On Mon, 2016-02-29 at 15:06 +0100, Rutger Vlek wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
The CA3080 is known to be a bit noisy, but if you find it everywhere (even in the ground) I'd do a more fundamental check on your power supply and measurement setup.<br>
<br>
How do you supply the board with power? How do you do the audio trace exactly? Just to be sure that the noise is actually in the board, not in the measurement method :).<br>
<br>
Rutger<br>
<br>
<br>
<br>
On 29 feb 2016, at 03:46, Joe wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hello there, I built this panning VCA and I am happy with how it sounds<br>
except there is a lot of background noise. I tried to audio trace the<br>
noise but I find it everywhere, even in the ground plane. Is there some<br>
advice that someone can give me about how to isolate it. Thanks.<br>
<br>
On Sat, 2016-01-23 at 12:58 -0500, Joe wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Thanks to all! You guys are the awsomest ever! Joe.<br>
<br>
<br>
<br>
<br>
On Fri, 2016-01-22 at 16:13 -0500, Joe wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
I am planning on building this single as a panning VCA by Richard<br>
Curcio.<br>
<br>
<a href="http://www.sdiy.org/richardc64/mmvca/index.html" rel="noreferrer" target="_blank">http://www.sdiy.org/richardc64/mmvca/index.html</a><br>
<br>
I can source a CA3080 and since I am only building one I am not worried<br>
about expense. Here's the thing, I don't know what pot values to use for<br>
the trimmers and I am definitely thrown by the current controlling DC<br>
trimmer, though I understand how to wire it. Can anyone take a minute(or<br>
few) to help me figure them out? Thanks, Joe.<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl" target="_blank">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
</blockquote>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl" target="_blank">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
</blockquote>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl" target="_blank">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
</blockquote></blockquote>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl" target="_blank">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
<br>
</blockquote></blockquote>
<br>
<br>
</blockquote>
<br></div></div><span class="im HOEnZb">
-- <br>
BugBrand LTD<br>
UK company No. 07199808<br>
VAT No. GB 988 2629 57<br>
1 Ninetree Hill<br>
BRISTOL BS1 3SB<br>
United Kingdom<br>
<a href="http://www.bugbrand.co.uk" rel="noreferrer" target="_blank">www.bugbrand.co.uk</a><br>
<br></span><div class="HOEnZb"><div class="h5">
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@dropmix.xs4all.nl" target="_blank">Synth-diy@dropmix.xs4all.nl</a><br>
<a href="http://dropmix.xs4all.nl/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://dropmix.xs4all.nl/mailman/listinfo/synth-diy</a><br>
</div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature">[s]</div>
</div>