<div dir="ltr">Wow - thank you everyone for the responses, it's nice to wake up in the morning and read all of these perspectives on my questions..<br><br>Just to clarify a few things: <br><div><br></div><div>I do want to drive speakers. I'm essentially talking about a pre-amp and a power amp in a single design. It sounds like I should worry about getting one of them right before trying to get both of them right :) </div><div><br></div><div>Re: power amp - <br>I need to match a few impedances. I know that the circuit that I shared outputs for 8-ohm matching, but I'm also going to need an output for driving items with 1k impedance.  I'm attempting to drive some transducers besides regular speakers - piezo elements, for example. </div><div><br></div><div>I would be interested in better, simple driver circuits, if people have suggestions. I didn't realize the one I shared was so flawed. I had experimented with the lm386 in the past and been very frustrated - I also wanted to make sure I had something that worked on a bipolar scale, which I had a bit of trouble finding. </div><div><br>Re: pre-amp - </div><div><br></div><div>I wanted to use a transformer to bring up the level of some pretty quiet microphone elements. I messed with voltage gain and didn't seem to have a lot of luck. There are probably a number of other alternatives to investigate - it seems like I should worry more about setting proper impedance with resistors- but just to clarify what seems to be the consensus here: there is no reason to use a transformer at the input of a preamp? <br></div><div><br></div><div><br></div><div>Thanks everyone..</div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Aug 19, 2015 at 6:36 AM, Neil Johnson <span dir="ltr"><<a href="mailto:neil.johnson71@gmail.com" target="_blank">neil.johnson71@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi,<br>
<span class=""><br>
> i'm currently (perpetually) trying to wrap my head around some basic<br>
> electronics ideas and i was hoping to ask a few questions.<br>
<br>
</span>Execllent!<br>
<span class=""><br>
> at the moment, i'm trying to design a small amplifier. based on this one, to<br>
> be precise:<br>
> <a href="http://www.allaboutcircuits.com/textbook/experiments/chpt-6/class-b-audio-amplifier/" rel="noreferrer" target="_blank">http://www.allaboutcircuits.com/textbook/experiments/chpt-6/class-b-audio-amplifier/</a><br>
<br>
</span>I would strongly recommend completely ignoring that circuit.  It has<br>
far too many problems to list.  There are much simpler, better, and<br>
understandable circuits around for driving a small speaker.  Just<br>
delete that page from your screen, erase the circuit from your memory,<br>
and have a quiet moment to ponder the nature of the internet....<br>
<span class=""><br>
> i have the following questions:<br>
> 1. to drive a speaker, the current is scaled up considerably - is it safe to<br>
> send it back into an op amp? i know that operational amplifiers<br>
> theoretically reject current, but how do i determine their limits? and does<br>
> high current impact offset voltage?<br>
<br>
</span>The ideal model of an op-amp is no current into the inputs.  So you're<br>
safe in not pushing any current into the op-amp (unless you exceed the<br>
safe voltage!).<br>
<span class=""><br>
> 2. if i use a transformer at the output, i could potentially be stepping up<br>
> the voltage considerably - is that safe to send that back into an op amp?<br>
<br>
</span>Depends on what the output is (see question below about what you mean<br>
by "line level").  If the voltage is too high then you can always use<br>
a potential divider to reduce it.<br>
<span class=""><br>
> my main reason for asking is that i'm interested in using line-level devices<br>
> within a +/-12v system, so i know they need to be stepped-up via transformer<br>
> at some point.. i'm essentially wondering if it's possible to use one<br>
> transformer for multiple functions.<br>
<br>
</span>What do you mean by "line level"..?  Do you mean the 100V line system<br>
used in PA systems?<br>
<br>
Cheers,<br>
Neil<br>
--<br>
<a href="http://www.njohnson.co.uk" rel="noreferrer" target="_blank">http://www.njohnson.co.uk</a><br>
</blockquote></div><br></div>