[sdiy] [semi-ot] making patch cables with thin console cable.

[cheater cheater]

I suggest this recent video as a great dip into the different kinds of
gold plating. It doesn't even cover 1%:
https://www.youtube.com/watch?v=ZUvioHb6N8g

On Sun, Sep 6, 2026 at 8:05 PM Michael E Caloroso via Synth-diy
<synth-diy at synth-diy.org> wrote:
>
> "Gold plated" is a very vague description loosely thrown around a lot.  Many datasheets do not reveal anything about alloys mixed with the gold, how thin the plating is, or how many carats the gold is!  Caveat emptor.
>
> Consumer level low cost gold plated plugs/jacks are to be avoided.  Besides the unspecified purity of the plating, the plating is extremely thin (usually under 10um) and will wear off with repeated insertions - some datasheets report a maximum life of ten insertions!  Once the plating is breached, that exposes the underlying metal which corrodes or oxidizes very quickly when exposed to air.  My experience with gold plated plugs was disappointing enough that I never repeated the experience.
>
> The only applications of gold plated interconnects in my studio are board-to-board interconnects for critical power rail and CV lines, which I had installed in my Memorymoog and other synths with great success.  Of course those interconnects are military grade components with minimum 10um plating and high purity gold.  The oldest ones are 30+ years old and still free of problems.
>
> Tin plating on plugs does corrode/wear off, albeit over much longer time.  I have stage cables that I built over 40 years ago; they got a lot of use and the tin plating of the Switchcraft plugs finally wore off after 25 years of heavy use, exposing the underlying brass core material which oxidized quickly thus requiring replacing the plugs.  Amazingly the original Columbia raw cable is still going strong.  Thinking that the non-copper strands in the cable can oxidize (I've had it happen), I just checked the conductance between solder joints (two wire measurement on DMM) on the plugs; 5 of 7 cables registered zero ohms, the worse reading of the other two was 0.3 ohms.  And during the process, I caught a plug in its early stage of corrosion on the sleeve plating.
>
> MC
>
> On Sun, Sep 6, 2026 at 11:53 AM Mattias Rickardsson <mr at analogue.org> wrote:
>>
>> I don't have any good advice on what exact product to buy, but it seems like a general "avoid the lowest-budget end" makes sense. Half a year ago I bought 10 of the cheapest gold-plated plugs available at Digi-Key or Mouser or Farnell - don't remember more than that they were very cheap but at least gold-plated - for just making zero-ohm shorted testing plugs for a project.
>>
>> When using them I was surprised to experience that some of them didn't fit the jacks properly. The tip, the ring, and the plastic insulation piece in between them were not really aligned well, so they ended up slightly too large to fit in some jacks where I'd never had any problems with any plugs for 15 years.
>>
>> And last week I noticed that all of them had a lot of corrosion/dirt on the "gold". After half a year! My other cables in the same place are still fine after 10+ years, being some mid-price Cordial product with at least a brand name on the actual plugs.
>>
>> I guess you often get what you pay for. :-)
>>
>> /mr
>>
>> Den lör 5 sep. 2026 18:45Jimmy Moore via Synth-diy <synth-diy at synth-diy.org> skrev:
>>>
>>> I got a great deal on a spool of mogami w2944, so time to revive the patchbay project.   This is console wire, so has a very thin OD of about 2.54mm:
>>>
>>> https://mogamicable.com/category/bulk/console/#gsc.tab=0
>>>
>>> I foresee this causing some challenges with audio jacks that are designed around much beefier wire.
>>>
>>> I'm curious if anyone had suggestions for preferred (1/4") connectors for this kind of thing.  I have a samson S-patch plus, so no TT or bantam jacks for me just yet.
>>>
>>> I suspect the recommendation will be heat shrink tubing + neutrik jacks. I would love to hear what you think.
>>>
>>> jimmy
>>>
>>> PS: if anyone has some spare jacks or heat shrink you would be interested to sell, let me know!
>>>
>>>
>>> ________________________________________________________
>>> This is the Synth-diy mailing list
>>> Submit email to: Synth-diy at synth-diy.org
>>> View archive at: https://synth-diy.org/pipermail/synth-diy/
>>> Check your settings at: https://synth-diy.org/mailman/listinfo/synth-diy
>>> Selling or trading? Use marketplace at synth-diy.org
>>
>> ________________________________________________________
>> This is the Synth-diy mailing list
>> Submit email to: Synth-diy at synth-diy.org
>> View archive at: https://synth-diy.org/pipermail/synth-diy/
>> Check your settings at: https://synth-diy.org/mailman/listinfo/synth-diy
>> Selling or trading? Use marketplace at synth-diy.org
>
> ________________________________________________________
> This is the Synth-diy mailing list
> Submit email to: Synth-diy at synth-diy.org
> View archive at: https://synth-diy.org/pipermail/synth-diy/
> Check your settings at: https://synth-diy.org/mailman/listinfo/synth-diy
> Selling or trading? Use marketplace at synth-diy.org