[sdiy] Operating voltages questions about synthesizers

[Michael E Caloroso]

Not all discrete transistors will work at higher voltage so you need
the datasheet for those transistors for those OEMs.  I found out the
semi-hard way when using 2N2222 NPN in a circuit (there's a REASON why the
2N2222A was made available).

Same with any ICs.

Electrolytics and tantalums do not like their maximum voltage rating
exceeded.

You really need to analyze the entire circuit AND the active devices used
before changing the supply voltage.  Not at all trivial.

MC

On Mon, Sep 5, 2022 at 5:13 AM Roman Sowa <modular at go2.pl> wrote:

> Depends what you call "sounds better".
>
> AFAIK input voltage, 9V in original, and 12V in your case is only used
> for speaker amplifier, comparator, and pullup resistors for OTA outputs
> in the filter.
> So the power amp may feel better, able to provide more power at lower
> distortion. For comparator it doesn't mean a thig. And for OTAs, well it
> changes the voltage of the output pullup resistor higher than OTA's
> power suply. That may affect how it works, introducing some nice
> distortion, increase levels, or whatever, but I'm only guessing here.
>
> The thing is, most of the circuit is powered from internal 6V regulator
> made with TO92 transistor, so if you change input from 9 to 12V, it has
> to dissipate twice more heat than before. Probably not much anyway, but
> it's easy to check with your finger.
>
> First thing I woudl do is to check current draw, how it changes when
> supply rises from 9 to 12. Next is to check how signal changes at OTA
> outputs.
>
> Roman
>
>
> W dniu 2022-09-05 o 09:33, Logan Mitchell Sr via Synth-diy pisze:
> > I am finally working on completing modifying my Electro-Harmonix EH 0400
> > mini synthesizer that I purchased brand new around 1979/1980.
> >
> > Its original factory power supply was two 9-volt batteries connected in
> > parallel with no external power supply adapter jack installed so I
> > installed one some years ago to use a 9 volt DC power supply.
> >
> > Last night I connected a 12 volt DC power supply & noticed that the
> > synthesizer sounded a little better than when operating from the 9 volt
> > battery or from the 9 volt DC power supply.
> >
> > I'm thinking about adding a 7812 or 7815 voltage regulator circuit to
> > connect to the power connection of this synthesizer since I have some 18
> > volts DC power supplies (wall warts) that I've used on some other
> > electronic music devices.
> >
> > My question is this - does an electronic music circuit that works fine
> > from a 9 volt DC supply work even better at 12 or 15 volts DC & why is
> > that so ?
> >
> > Logan
> >
> >
> >
> > _______________________________________________
> > Synth-diy mailing list
> > Synth-diy at synth-diy.org
> > http://synth-diy.org/mailman/listinfo/synth-diy
> > Selling or trading? Use marketplace at synth-diy.org
> >
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at synth-diy.org
> http://synth-diy.org/mailman/listinfo/synth-diy
> Selling or trading? Use marketplace at synth-diy.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20220905/fa4489a6/attachment.htm>