[sdiy] Off topic - removal of sticky microphone whole-body coating

[cheater cheater]

Did it hold up well?

On Sat, Nov 27, 2021 at 5:40 PM Ben Stuyts <ben at stuyts.nl> wrote:
>
> Haha, that was actually one of the options I considered. I have a dual head printer with which I’ve printed ABS wheels with TPU tires in one go. For a luggage trolley, not a synth. :-)
>
> Ben
>
>
> > On 27 Nov 2021, at 17:06, Mike Bryant <mbryant at futurehorizons.com> wrote:
> >
> > They'll probably sent you a 3D printing file for a replacement :-)
> >
> > -----Original Message-----
> > From: Synth-diy [mailto:synth-diy-bounces at synth-diy.org] On Behalf Of Ben Stuyts
> > Sent: 27 November 2021 15:29
> > To: MTG
> > Cc: synth-diy at synth-diy.org
> > Subject: Re: [sdiy] Off topic - removal of sticky microphone whole-body coating
> >
> > My Moog Sub-37 has the same problem with both mod wheels. I hadn’t touched it in a few years. Unplayable, and cleaning didn’t really help. (Tried soap, IPA, windex.) I also have a Subsequent-37 CV and it has no such problems. So I contacted Moog and they are aware of the problem. They hope to have a solution for me in a few months.
> >
> > Ben
> >
> >
> >> On 27 Nov 2021, at 01:34, MTG <grant at musictechnologiesgroup.com> wrote:
> >>
> >> It seems like the whole world is going to melt. A new plague. They must have known this material would disintegrate in a relatively short time. I've had to clean binoculars, keypads and TV remotes so far (using just about everything in the house, including just scraping a lot of it off). I think alcohol was about the best, both for me and the cleaning.
> >>
> >> On 11/26/2021 3:25 PM, Mike Bryant via Synth-diy wrote:
> >>> Not sure about that device, but it’s possibly the handling noise reduction rubber coating.  Nothing you can do to stop it suffering what is known as rubber reversion.  Various alcohols will clean it off, but then the microphone won’t be suitable for any form of hand-holding, and you’ll need a good anti-vibration mounting which makes removing it a bit pointless.
> >>> Lots of mixers suffer the same problems with their knobs, but those just pull off and replace.
> >>> *From:*Synth-diy [mailto:synth-diy-bounces at synth-diy.org] *On Behalf
> >>> Of *Logan Mitchell Sr via Synth-diy
> >>> *Sent:* 26 November 2021 23:13
> >>> *To:* synth-diy at synth-diy.org; analogue at hyperreal.org
> >>> *Subject:* [sdiy] Off topic - removal of sticky microphone whole-body
> >>> coating Hello.
> >>> I know that this is off-topic. I have a Coby CM-P35 Lo-Z 500 ohm Dynamic microphone with a removable windscreen whose entire metal body has a coating on it that has turned sticky.
> >>> What is a good solution to use to remove this sticky coating without ruining the mic body's original finish ?
> >>> Does anyone know why this type of coating would have been used ? I've seen it used on other types of electronic items.
> >>> Logan
> >>> _______________________________________________
> >>> Synth-diy mailing list
> >>> Synth-diy at synth-diy.org
> >>> http://synth-diy.org/mailman/listinfo/synth-diy
> >>> Selling or trading? Use marketplace at synth-diy.org
> >> _______________________________________________
> >> Synth-diy mailing list
> >> Synth-diy at synth-diy.org
> >> http://synth-diy.org/mailman/listinfo/synth-diy
> >> Selling or trading? Use marketplace at synth-diy.org
> >>
> >
> >
> > _______________________________________________
> > Synth-diy mailing list
> > Synth-diy at synth-diy.org
> > http://synth-diy.org/mailman/listinfo/synth-diy
> > Selling or trading? Use marketplace at synth-diy.org
> >
>
>
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at synth-diy.org
> http://synth-diy.org/mailman/listinfo/synth-diy
> Selling or trading? Use marketplace at synth-diy.org