[sdiy] ODP: Re: Quantizer project.. incoming CV's switching point to change to quantized output CV's ...

Roman modular at go2.pl
Tue Jul 13 07:06:31 CEST 2021


My personal experience is that I'd rather spend $5 more on good linearity high resolution DAC than hassle with calibration of each note. Even if the calibration process is automated. 

Roman

---- Użytkownik Oren Leavitt via Synth-diy napisał ----

>I like that idea of a fine tuning DAC, too.
>
>Something I've experimented with in a MIDI to CV is to have one 
>dedicated DAC for octaves, and another 12 or 16 bit DAC for just the 
>note offset in between. The note value would be fetched from a lookup 
>table for whatever tuning was selected. The octave was simply the MIDI 
>note number modulo the length of the selected tuning table. The note 
>offset was the remainder.
>
>The analog outputs from the two DACs are summed together for the final CV.
>
>It worked out surprisingly well!
>
>I would imagine this would work equally well for the quantizer project 
>as well.
>
>On 7/7/21 8:38 PM, Brian Willoughby wrote:
>> This is an excellent suggestion, and should work for anything except very open tuned chords.
>>
>> Even with wide chords, if each VCO gets its own Coarse and Fine then it will still work just fine.
>>
>> One thing I was going to suggest is that the Coarse "DAC" could just be a set of switched resistors (or voltage references) that can produce exact 1 V steps. With 1V/octave, the Coarse could just select the octave range (and the Fine would not necessarily be limited to one octave).
>>
>> Brian
>>
>>
>> On Jul 7, 2021, at 11:50, Jay Schwichtenberg via Synth-diy <synth-diy at synth-diy.org> wrote:
>>> Very simple solution for this.
>>>
>>> Just like for a regular VCO have a course and fine tune DAC, maybe 12-14 bits for the course and 8-10 bits for the fine. Just make sure they are decent DACs, especially that they are linear.
>>>
>>> Timing as far as writing both values shouldn't be a problem. One solution if you think it might would be use a dual DAC for both that has a sync function (output values and then send command to load the DACs simultaneously).
>>>
>>> Jay S.
>>>
>>> On 7/6/2021 10:19 PM, Brian Willoughby wrote:
>>>> In order to hit 701.995 cents, I assume you'll need a resolution of 0.005 cents on your DAC. If I'm doing the math correctly, that requires an 18-bit DAC, and I don't know any with DC output. That's just for 1 octave of range. If you want 5 octaves of range, you'll need a 20-bit DAC.
>>>>
>>>> Are you talking about a practical design, Mike?
>>>>
>>>> I know that 20-bit ADC and DAC were a thing before 24-bit delta-sigma, but I never went looking before. The first 18-bit DAC I found only guarantees 12-bit accuracy, but at least it's monotonic. I suppose one could spend more than $10 to get better accuracy.
>>>>
>>>> Brian
>>
>> _______________________________________________
>> Synth-diy mailing list
>> Synth-diy at synth-diy.org
>> http://synth-diy.org/mailman/listinfo/synth-diy
>> Selling or trading? Use marketplace at synth-diy.org
>_______________________________________________
>Synth-diy mailing list
>Synth-diy at synth-diy.org
>http://synth-diy.org/mailman/listinfo/synth-diy
>Selling or trading? Use marketplace at synth-diy.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20210713/07b30236/attachment.htm>


More information about the Synth-diy mailing list