[sdiy] SSI2130

David G Dixon dixon at mail.ubc.ca
Sat Sep 19 21:40:24 CEST 2020


DItto -- what Oren said.  Make the pins 0.6" apart.  I'd buy that.

  _____  

From: Synth-diy [mailto:synth-diy-bounces at synth-diy.org] On Behalf Of Oren
Leavitt
Sent: Saturday, September 19, 2020 11:24 AM
To: synth-diy at synth-diy.org
Subject: Re: [sdiy] SSI2130



Looks nice!

Why not just go with a 0.6 inch wide DIP format? It'll fit a standard 0.6
wide DIP socket and you'll have a little more wiggle room.

It's a VCOduino!

- Oren


On 9/19/20 12:40 PM, Pete Hartman wrote:


I was inspired last night to take a crack at the idea of a breakout that
could have the chip pre-soldered.  I don't normally do a lot of work with
finer pitch SMD so I found I had to use fairly fine traces to route to the
pins with the chip rotated (which seemed to make the most sense, since going
to a DIP form factor).  Necking in KiCad is not something I've mastered and
I didn't spend a lot of time when I found it wasn't working the way I
thought the descriptions online said it should.  PS: not looking for a
debate about CAD packages ;). 

I'm curious if any of the more experienced would have any opinions they'd
care to offer?  Full disclosure: the intent is for this to be sold as a DIY
tool, so if providing advice for what might become a low volume commercial
product is a concern, by all means, don't feel like you are obligated to
comment.

First the images.  I'm also sending pictures to the list for the first time,
so if for some reason this doesn't work, I can always throw links to my
google drive up pretty quickly.


Screen Shot 2020-09-19 at Sep 19 12.05.02PM.png       Screen Shot 2020-09-19
at Sep 19 12.06.12PM.png

I liked the idea of having the regulator(s) on board, so I dug around to
find a couple that seemed likely.  I did find that -V regulators were
significantly more expensive (Q100 of both of these are under $0.30,  Q10,
and I didn't look for Q100, of even a pretty basic - regulator was on the
order of $3.00).  Since the chips tolerates up to -18V I decided to forego a
regulator on the negative rail.

The V+ equivalent pin feeds the TLV1117-50, and that 5V feeds the MCP1700-25
as well as the actual V+ pin on the chip.  I figured someone might want to
use their own different 2.5V reference so I put a normally closed set of
jumper pads that could be cut if preferred (like the USB power on a teensy,
for example).  This also allows you to take the 2.5V reference *off* the pin
if you wanted to use it for expo scaling, or through zero, etc.  Sitting
here this morning I am thinking it might be a good idea to provide an extra
pin at the top edge so the 5V reference could be treated similarly.  I don't
think I could do exactly the same thing because there has to be some way for
the higher voltage to get onto the breakout.

All the caps are 0603, which is about as small as I'd want to hand solder;
although I do not intend to hand solder it myself, I figured leaving the
option open even if just for prototyping seemed like a good idea.  Same idea
behind using "handsolder" footprints for the regulator & reference.

It's half an inch between the rows of pins and .7" wide by 1.7" long total.

Thoughts?

Thanks!

Pete

 
_______________________________________________

Synth-diy mailing list

Synth-diy at synth-diy.org

http://synth-diy.org/mailman/listinfo/synth-diy

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20200919/79a02f22/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Screen Shot 2020-09-19 at Sep 19 12.05.02PM.png
Type: image/png
Size: 96111 bytes
Desc: not available
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20200919/79a02f22/attachment.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Screen Shot 2020-09-19 at Sep 19 12.06.12PM.png
Type: image/png
Size: 54864 bytes
Desc: not available
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20200919/79a02f22/attachment-0001.png>


More information about the Synth-diy mailing list