[sdiy] blowing fuses

ColinMuirDorward colindorward at gmail.com
Sun Feb 16 19:04:51 CET 2020


Unfortunately, there seems to be no mention of a fuse.

On Sun, Feb 16, 2020, 9:46 AM Richie Burnett, <rburnett at richieburnett.co.uk>
wrote:

> Usually the rating label tells you what fuse to fit?
>
> -Richie,
>
>
>
> -----Original Message-----
> From: ColinMuirDorward
> Sent: Sunday, February 16, 2020 2:43 PM
> To: Richie Burnett
> Cc: *SYNTH DIY
> Subject: Re: [sdiy] blowing fuses
>
>
> Thanks Richie.
> I should have mentioned, it's a transformer/linear supply.
> Not only us it eating fuses for breakfast, but dinner, too. In a couple
> hours, I'll be able to test lunch.
> So I suppose there is some faulty (or non-existant) inrush current
> protector, and it's costing me one fuse to charge up whatever is sucking
> those amps?
>
>
>
> On Sun, Feb 16, 2020 at 12:36 PM Richie Burnett
> <rburnett at richieburnett.co.uk> wrote:
> If it's a SMPS the inrush current at turn-on will probably eat quick-blow
> fuses for breakfast.
>
> -Richie,
>
>
>
> -----Original Message-----
> From: ColinMuirDorward
> Sent: Sunday, February 16, 2020 2:21 PM
> To: *SYNTH DIY
> Subject: [sdiy] blowing fuses
>
>
> Maybe someone has some suggestions for me.
>
> I'm blowing fuses on my "industrial" power supply. This is a salvaged
> +/-15v, 3a supply housed in a rugged metal enclosure. I've wired it up with
> a fuse on the AC mains side, and fuses on the +/-15v side. The AC/mains
> fuse
> is giving me grief.
>
> Step1) I can turn the unit on, and everything is fine. My synth is only
> drawing 1/2 an amp (or nothing when disconnected).
> Step2) Turn the unit off. At this point, I can remove the mains fuse, and
> test it: yes, still good.
> Step3) Re-install fuse, switch on. Nothing. Remove fuse and test again, now
> it's blown.
> Step4) Install new fuse. Go to Step1)
>
> I haven't used the PSU much yet, but I've powered it on and off loads of
> times and this problem never manifested till now. The fuses are 2amp, 250v,
> which I think is fine, but here is maybe my mistake: they are quick blow
> type. I'm uncertain, though. Wondering if I need to try to find a fault in
> the PSU, or just order the new fuses. But why didn't those quick blow fuses
> break before?
>
> Thanks for reading!
> Colin
>
>
> --
>
> https://www.instagram.com/colinmuirdorward/
> -
>
> https://www.instagram.com/ssdp_synthesis/
>
> Virus-free. www.avg.com
>
>
>
>
>
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at synth-diy.org
> http://synth-diy.org/mailman/listinfo/synth-diy
>
>
>
>
> --
>
> https://www.instagram.com/colinmuirdorward/
> -
>
> https://www.instagram.com/ssdp_synthesis/
>
> Virus-free. www.avg.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20200216/b9965584/attachment.htm>


More information about the Synth-diy mailing list