[sdiy] IR Reverb

Bruno Afonso bafonso at gmail.com
Sun Feb 18 20:20:21 CET 2018

If you're willing to go into DSP land then you could also look at blackfin,
Monome's Aleph uses open source tools for develop it. For STMs, the only
shot would be to attempt to use fixed point, not a lot of juice for
floating point stuff but like other's mention, it may be a lot of work..
maybe more for as a challenge? :)


On Sat, Feb 17, 2018 at 5:24 AM <rsdio at audiobanshee.com> wrote:

> I haven’t developed for SHARC, yet, but I can say that I shipped the
> Soundplane without spending much on the compiler/assembler. That was based
> on the TMS320VC5506, a member of the lowest-power C55x line. You might want
> to look at the C6000 series or OMAP, such as the OMAP-L1x line. I recall
> that the tools run free when you have one of the evaluation boards
> connected to your computer.
> What about some of the less “fancy" SHARC DSP options, like the ADSP-2191M
> used in the DSI eVoLver? For some reason, I assume that a 16-bit DSP would
> cost less. Dave (and/or his firmware programmer) managed to coax 24-bit
> audio out of this 16-bit DSP by using specific features. I haven’t looked
> into the tools for that chip, but maybe they’re priced lower than the tools
> for the flagship chips.
> Brian
> On Feb 16, 2018, at 3:50 PM, Tim Ressel <timr at circuitabbey.com> wrote:
> > I hear ya. My comment about the cost of tools referred to the compilers.
> I'd love to use a Sharc, but it looks like at least $1K for the compiler.
> >
> > --tr
> >
> > On 2/16/2018 1:48 PM, rsdio at audiobanshee.com wrote:
> >> You really need a DSP for this, and not a general-purpose CPU like ARM.
> Even though ARM has a DSP instruction or two, it's a far cry from a total
> system designed for signal processing. Families like the TMS320 have been
> evolving for decades - literally 35 years - to optimize this sort of thing.
> Literally every aspect of the chip has been tweaked to optimize signal
> processing.
> >>
> >> Texas Instruments has cheap demo platforms with audio I/O and the tools
> come free with those $50 evaluation boards. There are a lot of open-source
> routines, so if you need FFT in TMS320 assembly then it's there. You can
> call that from C and keep your overall design simple.
> >>
> >> Texas Instruments even has chips that are dual-processor inside - one
> TMS320 for DSP, plus and ARM for the higher level stuff and maybe even some
> audio processing. Look for OMAP chips. The C6000 series of DSP would be a
> good choice because it supports floating point (I've worked with the C5500
> series that is fixed point, and that's a lot of tedium but worth it if you
> want to run off of batteries).
> >>
> >> Another good option would be SHARC.
> >>
> >> If you choose a non-DSP chip, everything will be less efficient. That
> either means loss of features or higher temperatures and shorter battery
> life.
> >>
> >> Brian Willoughby
> >> Sound Consulting
> >>
> >> On Feb 16, 2018, at 11:47 AM, Tim Ressel <timr at circuitabbey.com> wrote:
> >>> I wonder if it would be possible to do a parallel processor scheme
> where one proc handles the early stuff and another to handle the longer
> time stuff. each proc would output via a codec and those outputs would get
> summed. Hmm...
> >>>
> >>> On 2/16/2018 11:38 AM, Eric Brombaugh wrote:
> >>>> I suspect that STM32 doesn't have the horsepower you'll need to do a
> useful IR reverb. There are several fairly efficient FFT in the CMSIS
> libraries from ARM but even using those the best you can do is about a 4096
> FFT running at less than 48kHz with long latency and large overlaps.
> >>>>
> >>>> On 02/16/2018 12:24 PM, Tim Ressel wrote:
> >>>>> Still, even with all that jigery-pokery, we're going to need a
> bigger boat, er, processor. I'd like to avoid processor choices that needs
> pricey tools. STM32 would be nice. Of course some good ol' fashion assembly
> code, highly optimized, would help things. Its been a while since I went
> down that rabbit hole. I wonder if someone has an optimozed FFT library for
> Cortex Mn�
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at synth-diy.org
> http://synth-diy.org/mailman/listinfo/synth-diy
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://synth-diy.org/pipermail/synth-diy/attachments/20180218/3d221920/attachment.htm>

More information about the Synth-diy mailing list