[sdiy] measuring dc current max/draw of psu with a scope or multimeter??

[blacet at blacet.com]

Using a DMM is easy but you would have to break the connection between the
PS and the load to insert the DMM. With the Blacet PS800 and PSCONN3, you
could just break one of the wires from the PS800  (+ or -), insert the DMM
(in current mode!) and measure. Power down and remove the DMM and
reconnect the wire break.


> How about just get a digital multimeter from Harbor Freight for $6 or
> for free when they have a coupon ?
>
> http://www.harborfreight.com/7-function-digital-multimeter-90899.html
>
>
>
> On 12/10/2015 8:07 AM, Richie Burnett wrote:
>> You need to be careful with grounding if you use a current sensing
>> resistor and an oscilloscope to measure current draw from a power
>> supply.  For instance, if both the power supply and oscilloscope are
>> grounded to the mains supply earth, and you put the current-shunt
>> resistor in the V+ feed (high-side sensing) to measure the current
>> there, then you can't just connect one oscilloscope probe across the
>> resistor to measure the voltage drop.  Connecting the scope's ground
>> clip will short the V+ supply to ground through the scope, possibly
>> damaging either the scope or power supply!
>>
>> The solutions are:
>>
>> 1. Power the scope from an isolation transformer.
>> 2. Use a battery powered "Scopemeter" that isn't earthed.
>> 3. Run the power supply from an isolation transformer with it's earth
>> floated.
>> 4. Use a Class-II power supply that isn't earthed.
>> 5. Use two scope probes to measure the voltage drop in (Y1-Y2)
>> differential measurement mode.
>> 6. Move the sense resistor into the 0v line of the power supply and
>> connect the scope probe ground lead to the PSU ground side.
>>
>> Note, method 6 is only acceptable if the current flowing in the 0v
>> line is the same as the current you wanted to measure.  This is fine
>> for something like a single output +12V power supply, but measuring
>> the ground current won't work for a multi-output +5V/-12V/+12V power
>> supply where all of the wires will likely carry different currents.
>>
>> Hope this helps,
>>
>> -Richie,
>>
>>
>>
>> -----Original Message----- From: Vladimir Pantelic
>> Sent: Thursday, December 10, 2015 2:58 PM
>> To: synth-diy at dropmix.xs4all.nl
>> Subject: Re: [sdiy] measuring dc current max/draw of psu with a scope
>> or multimeter??
>>
>> On 10.12.2015 15:48, Dan Snazelle wrote:
>>> im trying to figure out if this is possible witn regular tools
>>>
>>> i know i could buy a dc ammeter but those are expensive
>>>
>>> ive also read about current probes but some of these seem to saturate
>>> at 500ma dc
>>>
>>> so
>>>
>>> i figured there must be a way to test current with a resistor and
>>> voltage
>>>
>>>
>>> any ideas??
>>
>> if you put a 0.1 Ohm resistor in-line with the PSU, then a current of 1A
>> will give you a voltage of 0.1V that you can read/measure with the
>> scope. if the voltage drop is too high, you can go to a lower resistance
>> as long as you can reliably measure the voltage. make sure the resistor
>> has a tight tolerance e.g. use a precision shunt.
>>
>>
>> _______________________________________________
>> Synth-diy mailing list
>> Synth-diy at dropmix.xs4all.nl
>> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>>
>>
>> -----
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 2016.0.7294 / Virus Database: 4483/11152 - Release Date:
>> 12/10/15
>> _______________________________________________
>> Synth-diy mailing list
>> Synth-diy at dropmix.xs4all.nl
>> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>>
>>
>
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at dropmix.xs4all.nl
> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>