[sdiy] midi and DIN sync in the one connector

Adam Inglis 21pointy at tpg.com.au
Wed Apr 29 10:03:22 CEST 2015


Yeah that's why I went with it, as my investigations triggering the  
voices with a square wave showed some nice tonal variation below 5  
volts.
(Well, actually, above 0 volts, as they are negative-going triggers  
from 5 to zero)

Adam
On 29/04/2015, at 5:27 PM, foRUMS 4 punkdISCO wrote:

> Nice.. That was the one I was looking at..
>
> I like the fact that it is velocity sensitive as I suspect the  
> CR8000 will
> give you different sounds with different voltages (despite it not  
> being
> velocity sensitive).
>
> Let us know how you get on..
>
> Ta,
>
> Paul
> London
> www.punkdisco.co.uk
>
>> -----Original Message-----
>> From: Adam Inglis [mailto:21pointy at tpg.com.au]
>> Sent: 29 April 2015 08:17
>> To: *SYNTH DIY
>> Subject: Re: [sdiy] midi and DIN sync in the one connector
>>
>> Elby Designs sell a 16 channel version
>>
>> http://www.elby-designs.com/contents/en-us/p959_MIDI2SDS-16.html
>>
>> I think I may even be able to fit it in the case
>>
>> Adam
>> On 29/04/2015, at 5:04 PM, foRUMS 4 punkdISCO wrote:
>>
>>> Hey Adam
>>>
>>> Ive thought about doing this to my CD8000.  Can I ask what Midi to
>>> Trig kit you will be using?
>>>
>>> Thanks,
>>>
>>> Paul
>>> London
>>> www.punkdisco.co.uk
>>>
>>>> -----Original Message-----
>>>> From: Adam Inglis [mailto:21pointy at tpg.com.au]
>>>> Sent: 29 April 2015 05:53
>>>> To: *SYNTH DIY
>>>> Subject: [sdiy] midi and DIN sync in the one connector
>>>>
>>>> I'm retrofitting my old Roland CR-8000 drum machine with a midi-to-
>>> trigger
>>>> board.
>>>> To minimise cosmetic disfiguration, I thought I might make the DIN
>>>> sync
>>> jack
>>>> do double duty for midi.
>>>> That way I could run a simple preset pattern and spice it up with
>>>> some
>>> extra
>>>> notes/fills here and there.
>>>> Does anyone know if there is likely to be any problems doing this,
>>>> say, caused by stray capacitance or crosstalk? The ground wire  
>>>> would
>>>> have to be shared.
>>>>
>>>> cheers
>>>> Adam
>>>> _______________________________________________
>>>> Synth-diy mailing list
>>>> Synth-diy at dropmix.xs4all.nl
>>>> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>>>
>>> _______________________________________________
>>> Synth-diy mailing list
>>> Synth-diy at dropmix.xs4all.nl
>>> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>>>
>>
>> _______________________________________________
>> Synth-diy mailing list
>> Synth-diy at dropmix.xs4all.nl
>> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at dropmix.xs4all.nl
> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
>




More information about the Synth-diy mailing list