[sdiy] Polivoks filter

[Adam Inglis]

Love the video.
It seems to me that you really want a finer control over this, because  
I felt the most musically interesting tones were lying just on that  
threshold in hard resonance just before it goes totally chaotic.
Also, there seemed to be a nice low end impact energy when you  
introduced some FM, good for percussion synthesis.

Adam
On 28/02/2013, at 4:49 PM, Dave Brown wrote:

> I received my front panel and finished building my Polivoks filter.   
> I updated the schematics and highlighted my few mods.  I put a 4  
> minute video showing some of the various modes and sounds.  I do  
> like this filter a lot and I like having both the soft and hard  
> resonance.  I like the soft resonance for traditional filter sound  
> and the hard resonance for adding somewhat uncontrolled edge to the  
> waveforms.  The tracking is pretty good although I haven't done a  
> complete test of the range of tracking.  The beginning of the video  
> demonstrates a sequencer driving both a VCO and the filter in self- 
> oscillation which tracks pretty well.  Since there is no fine  
> control the tuning is a bit tricky.
>
> http://modularsynthesis.com/kuzmin/polivoks/polivoks_vcf.htm
>
> Dave
>
> -----Original Message-----
> From: synth-diy-bounces at dropmix.xs4all.nl [mailto:synth-diy-bounces at dropmix.xs4all.nl 
> ] On Behalf Of Dave Brown
> Sent: Saturday, February 16, 2013 12:25 PM
> To: 'cheater cheater'
> Cc: 'synth-diy'
> Subject: Re: [sdiy] Polivoks filter
>
> I will.  Right now I think I will finish building it in a module  
> before using or recording.  It will be a lot easier and I don't risk  
> shorts with wires and cables flying everywhere.  A couple of times  
> now the weight of all the cables has pulled my PCB to the floor ...
>
> Dave
>
> -----Original Message-----
> From: cheater cheater [mailto:cheater00 at gmail.com]
> Sent: Saturday, February 16, 2013 11:00 AM
> To: Dave Brown
> Cc: synth-diy
> Subject: Re: [sdiy] Polivoks filter
>
> Hi Dave,
> that looks great! Would you like to record some demos and post wav's  
> somewhere?
>
> Thanks,
> D.
>
> On Sat, Feb 16, 2013 at 7:11 PM, Dave Brown <davebr at earthlink.net>  
> wrote:
>> I just finished hand building a Polivoks filter using the Marc
>> Bareille schematics with the reversing attenuator.  I ended up making
>> a couple of minor changes to reduce the filter to near unity gain and
>> softening the self-resonance output level so it would not clip rail  
>> to rail.
>>
>> I built this filter using NTE888M programmable op-amps since they are
>> readily available.  I did some frequency plots with my scope using XY
>> mode and was disappointed with the DC level shift I saw on the low  
>> pass output.
>> I got some of the УД1208 Russian parts to compare and discovered  
>> the
>> same DC shift.  I had repaired a Polivoks filter previously and the
>> frequency plots did not show any DC level shift.  I eventually  
>> figured
>> out the DC shift was occurring on the VCO output as I swept to high
>> frequencies.  I tried different VCOs and repeated the measurements
>> with a VCO that had a constant amplitude output with no DC shift over
>> the frequency range of the measurement.  Both the NTE888M and  
>> УД1208
>> Russian parts looked good with no DC shift in the low pass output.
>>
>> I saw only two minor differences between the NTE888M parts and the
>> УД1208 Russian parts.  The NTE888M parts have slightly higher gain  
>> and
>> the cutoff or center frequencies was slightly higher at the same
>> control settings and input CV.  I assume the frequency shift is due  
>> to
>> a slightly different Iset response curve or a different Vbe bias  
>> point for the Iset control pin.
>>
>> I have some uA776 parts on order and will also do the same comparison
>> (assuming the parts are genuine).
>>
>> Now I need to finish this filter with a front panel and play with  
>> it some.
>> Details, photos, and scope images are on my site on my Polivoks  
>> Filter page.
>> http://modularsynthesis.com/kuzmin/polivoks/polivoks_vcf.htm
>>
>> David J. Brown
>> Email davebr at earthlink.net
>> Website http://modularsynthesis.com
>
>
>
> _______________________________________________
> Synth-diy mailing list
> Synth-diy at dropmix.xs4all.nl
> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy