[sdiy] FS: Polymoog Synthesizer Parts

[Ken Elhardt]

I"m parting out my late model Polymoog Synthesizer 203a.  Manufacture
date 11/29/79 and SN# 4075, it was just about the last one Moog made
and the one Moog used as their NAMM demo unit.  For small parts there
is a small flat mailing fee of $2 for the US and Canada no matter how
much you buy.  If in Europe I'll have to calculate shipping.  For big
parts like the case/chassis/legs or heavy cast iron parts normal
shipping costs will apply.  Email me at elhardt (at) att (dot) net
with what you want, and I'll see if I still have it available.  And
NO, I don't have the Polypedals.  Thanks.


Parts $2 each
--------
* Slider Caps, Buttons, Wire Harnesses, other misc small parts (screws
free with purchase, just ask for any screws your Polymoog is missing,
and if I have them and don't need them, I'll throw them in)

Parts $3 each
--------
* Keys Black/White (these of course have the weights in them for that
heavy feel)

Parts $4 each
--------
* Dual Fine Tune/Beat Knob
* Polymoog Faceplate (the part around the preset buttons)

Parts $5 each
--------
* Polycom Boards (need to specify resistor value)

Parts $6 each
--------
* Polymoog Stickers (Black, Aqua Blue, Yellow, Red) with White Rounded
Retangular Border
* Polymoog Stickers (Black) without White Border
Printed on Orajet Vinyl with High Gloss Laminated Coating Ontop, can
also be used as bumper stickers.
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/MoogStickersSmall.jpg

Parts $20 each
--------
* Preset Button / LED Panel (that's the whole circuit board assembly
with wire harnesses)
* UA726 (was told these were worth $40 ea, saw someone else putting a
worth of $35 to one, but one can get NOS ones for about $34 from
europe, so perhaps used ones should be cheaper)

Parts $40 each
--------
Ribbon Pitch Controller (heard they go for $50 off of ebay, and $75 on ebay)

Parts $50 and $40 plus shipping (or both for $80) good for increasing
the value of a poor condition Polymoog especially if you plan to sell
it.
--------
* ($50+shipping) Case Top in almost perfect condition, with new custom
printed Moog sticker applied to replace the scraped up one currently
on there (if yours is beat to hell, this will make it look new again)
See pictures 6 & 7 below.
* ($40+shipping) Case Bottom, only has some very minor nicks and
scratches, some made less noticable with a black sharpie.  Could also
be painted.  (if yours is beat to hell and has big chunks busted out
of it, this will make it look a lot newer)
If these don't sell after some time, they'll be turned into a Polymoog
Coffee Table as per the dubsounds site.

* ($260+shipping) Polymoog & Rhodes, Legs/Braces/Knobs (half the price
of the new ones made by Vintage Music Parts) See picture 8 below.

* I've probably covered the most needed parts above.  Ask if you need
something else.


General Polymoog Synth Pictures
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog1.jpg
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog5.jpg

Control Panels Left and Right
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog2.jpg
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog3.jpg

Preset Button Panel
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog4.jpg

Case Top
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog6.jpg
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog7.jpg

Legs
http://i127.photobucket.com/albums/p122/Elhardt/Ebay/Polymoog8.jpg

-Elhardt