[sdiy] Should I use REAL PCBS or ETCHED

[harrybissell at wowway.com]

OK...

T42-1

oops my bad

H^) harry


On Thu, 14 Aug 2008 16:50:58 +0000, Dan Snazelle wrote
> i googled
> 
> Vector T42-A
> and searched MOUSER
> 
> nothing came up.
> 
> searching in the wrong places??
> 
> thanks
> 
> --------------------------------------------
> check out various dan music at:
> 
> http://www.myspace.com/lossnyc
> 
> http://www.soundclick.com/lossnyc.htm
> 
> http://www.indie911.com/dan-snazelle
> (or for techno) http://www.myspace.com/snazelle
> 
> > From: harrybissell at wowway.com
> > To: subjectivity at hotmail.com; pfperry at melbpc.org.au;
synth-diy at dropmix.xs4all.nl
> > Subject: RE: [sdiy] Should I use REAL PCBS or ETCHED
> > Date: Thu, 14 Aug 2008 11:44:51 -0500
> >
> > On Thu, 14 Aug 2008 15:56:52 +0000, Dan Snazelle wrote
> >
> >> harry-you mean you sell products that have vectorboard inside as the
> >> main boards?
> >
> > Mostly they are units I built for myself... still working since
> > College (mid 70's).
> >
> >>
> >> does perfboard present a nightmare situation though if THIS EVER
> >> NEEDS REPAIRS?? if i did etch or pcb house and a board went bad, i
> >> could just pull out the PNP template and make another. if i used
> >> perf, well it sounds like it would be hard. plus, doesnt vector or
> >> perfboard not hold up as well when soldering and resoldering (as in
> >> the case of replacing faulty parts,etc)
> >
> > Check out what the Vector T42-A terminal is. These are pushed into
> > the holes in the vectorboard. You wire to the bottom (usually) and
> > the components are on the top side... you can resolder hundreds of times
> > (on the component side) if you need to. I use the fiberglass perfboard
> > (not paper phenolic). Its tough stuff.
> >
> > H^) harry
> >
> >>
> >> thanks so much
> >>
> >> --------------------------------------------
> >> check out various dan music at:
> >>
> >> http://www.myspace.com/lossnyc
> >>
> >> http://www.soundclick.com/lossnyc.htm
> >>
> >> http://www.indie911.com/dan-snazelle
> >> (or for techno) http://www.myspace.com/snazelle
> >>
> >>> From: pfperry at melbpc.org.au
> >>> To: synth-diy at dropmix.xs4all.nl
> >>> Date: Fri, 15 Aug 2008 01:20:29 +1000
> >>> Subject: [sdiy] Should I use REAL PCBS or ETCHED
> >>>
> >>>
> >>> The answer varies for different people.
> >>> Personally, I find stripboard (aka veroboard) by far the best for me.
> >>> I notice that people who are significantly more intelligent than I, usually
> >>> prefer pad per hole board.
> >>>
> >>> paul perry Melbourne Australia
> >>>
> >>> _______________________________________________
> >>> Synth-diy mailing list
> >>> Synth-diy at dropmix.xs4all.nl
> >>> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
> >>
> >> _______________________________________________
> >> Synth-diy mailing list
> >> Synth-diy at dropmix.xs4all.nl
> >> http://dropmix.xs4all.nl/mailman/listinfo/synth-diy
> >
> >
> > Harry Bissell & Nora Abdullah 4eva
> >


Harry Bissell & Nora Abdullah 4eva