[sdiy] c&k on-on-on switches

[Tim Parkhurst]

See? I knew somebody more clever than I would figure this out just by
looking at the original info. I might have done it given several more
minutes of spare time, but Gene, you da man!


Tim ( < clever ) Servo

"Imagination is more important than knowledge." - Albert Einstein

*********************************************
> -----Original Message-----
> From: Gene Stopp [mailto:gene at ixiacom.com]
> Sent: Thursday, October 14, 2004 3:48 PM
> To: synth-diy at dropmix.xs4all.nl
> Subject: RE: [sdiy] c&k on-on-on switches
> 
> based on the fine explanation below, you can make this into a sp3t switch
by
> adding a jumper between 3 and 5. Then 2 becomes your common and you get
the
> following three poles:
> 
> Position 1 = 2 connects to 6
> Position 2 = 2 connects to 4
> Position 3 = 2 connects to 1
> 
> 
> 
> - Gene
> 
> 
> 
> -----Original Message-----
> From: owner-synth-diy at dropmix.xs4all.nl
> [mailto:owner-synth-diy at dropmix.xs4all.nl]On Behalf Of Tim Parkhurst
> Sent: Thursday, October 14, 2004 3:40 PM
> To: 'gregory zifcak'; synth-diy at dropmix.xs4all.nl
> Subject: RE: [sdiy] c&k on-on-on switches
> 
> 
> Okay, those were the 7211 switches, right? If so, then look at the data
> sheet in the link again. On page two, it shows the interconnect sequence
and
> pin numbers for the 7211 switch. The pins (looking from the bottom) are:
> 
> 
> 6     3
> 
> 5     2
> 
> 4     1
> 
> 
> And the sequence is:
> 
> Position 1 = 2 connect to 3, 5 connect to 6
> 
> Position 2 = 2 connect to 3, 5 connect to 4
> 
> Position 3 = 2 connect to 1, 5 connect to 4
> 
> Check the data sheet again, and you'll see the drawings showing the pin
> numbers the switch positions. Note that only one of the two sets of poles
> changes with each new switch position. I was kind of hoping for a more
> straightforward 1 to 4, 2 to 5, 3 to 6 sort of sequence, but I suppose
these
> will still be useful.
> 
> 
> Tim (ordered a few of those buggers myself) Servo
> 
> "Imagination is more important than knowledge." - Albert Einstein
> 
> **********************************************
> 
> 
> > -----Original Message-----
> > From: gregory zifcak [mailto:zifcak at hotmail.com]
> > Sent: Thursday, October 14, 2004 3:00 PM
> > To: synth-diy at dropmix.xs4all.nl
> > Subject: [sdiy] c&k on-on-on switches
> >
> > so,
> >
> > i got my on-on-on switches from goldmine today, does anyone know which
> pins
> > are which? i'm used to standard on-off-on dpdt switches. if these are
> > similar, which are the two contacts for the center on position? if it's
> dpdt
> > and on-on-on, wouldn't it need 2 poles + 3 more pairs of throws? i found
> > this, but it didn't seem to help:
> >
> > http://www.ittcannon.com/media/pdf/catalogs/Leaf/SW_toggle_7000.pdf
> >
> > thanks for any clues,
> > greg
> >
> > _________________________________________________________________
> > Express yourself instantly with MSN Messenger! Download today - it's
FREE!
> > hthttp://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
> >
> > ---
> > Incoming mail is certified Virus Free.
> > Checked by AVG anti-virus system (http://www.grisoft.com).
> > Version: 6.0.776 / Virus Database: 523 - Release Date: 10/12/2004
> >
> 
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.776 / Virus Database: 523 - Release Date: 10/12/2004
> 
> 
> 
> 
>
***************************************************************************
> This message is confidential.  The information contained in
> this e-mail message is intended only for confidential use of the
> recipient(s) named above. If the reader of this message is not the
intended
> recipient or an agent responsible for delivering it to the intended
> recipient, you are hereby notified that you have received this document in
> error and that any review, dissemination, distribution, or copying of this
> message is strictly prohibited.  If you have received this communication
in
> error, please notify us immediately by e-mail, and delete the original
> message.
>
***************************************************************************
> 
> ---
> Incoming mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.776 / Virus Database: 523 - Release Date: 10/12/2004
> 

---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.776 / Virus Database: 523 - Release Date: 10/12/2004
 



***************************************************************************
This message is confidential.  The information contained in
this e-mail message is intended only for confidential use of the
recipient(s) named above. If the reader of this message is not the intended
recipient or an agent responsible for delivering it to the intended
recipient, you are hereby notified that you have received this document in
error and that any review, dissemination, distribution, or copying of this
message is strictly prohibited.  If you have received this communication in
error, please notify us immediately by e-mail, and delete the original
message.
***************************************************************************