Fw: PAiA 9710 Manual Update (was Re: 9700 Power Supply Problem)

Grant Richter grichter at execpc.com
Wed Mar 15 19:25:40 CET 2000



----------
> From: John Simonton <honcho at paia.com>
> To: Grant Richter <grichter at execpc.com>
> Subject: PAiA 9710 Manual Update (was Re: 9700 Power Supply Problem)
> Date: Tuesday, March 14, 2000 11:24 PM
> 
> hi Grant- You and everyone else building toward a 9700S has the wrong
transformer. I had intended that a 15VADC transformer supplied with dual
9700 midi2cv8 orders be shipped with midi2cv8s going into 9700S but didn't
communicate that to everyone else :-( Now I'm making sure that the one that
I intended will do the job and we'll be sending one along to you and all
other system orders. I'm also changing this to be the transformer supplied
with any midi2cv8 order in the future.
> 
> Also- here's a notice that will be going to 9710 builders. The .pdf
mentioned won't really be up until Thursday.
> 
> 
> Feed-back from builders and further in-house verification have revealed
some errors in the 9710 Assembly/Using Manual supplied with your kit. A
revised  manual has been sent to the shipping address on your order and is
also available on-line at http://paia.com/9710man.pdf . 
> 
> Changes that impact assembly are listed below.
> 
> -------------------
> 
> Page 6 - most of the time, 100pFs disk capacitors are marked with 101.
> 
> Page 12 - step 2, for "...ends at that lug and at J11 so that....", 
'J11' should be 'J10'.
> 
> Page 12 - step 3,  for "...is on the left is #1.",  'left' should be
'right'.
> 
> Page 13 - p-p panel wiring; 'R110-3 (s1)' should read 'R110-3 (ns)'. Wire
M connects to R110-3 on page 15.
> 
> Page 13 - p-p panel wiring; the last in the group, to 'R113-2 (ns)'
should read 'R113-2 (s1)'.
> 
> Page 14 - step 2; 10k color code is listed as org-org-brn.  Should read
brown-black-orange.
> 
> Page 14 - step 5; '47k resistor (yellow-violet-orange)' should read '10k
resistor (brown-black-orange)'. If you were short a 47k resistor, this is
it. If you have already installed a 47k it will not affect performance.
> 
> Page 14 - step 6; 'through S2-2' should read 'through S1-2'.
> 
> Page 14 - In the last 5 steps Fig 4 and Fig 5 are interchanged.
> 
> Page 18 - step3/end of third paragraph; "...block, Q1 and D1 for
example." should be "...block, Q2 and D2."
> 
> Page 23 - second paragraph; "...of the IC7:C comparator,..." should read
"...of the IC7:D comparator,...:
> 
> -----------------------
> 
> I regret any inconvenience and frustration these errors have caused. If
you have any questions I'll do my best to help.
> 
> -John
> ---------------------------------------------------------
> John Simonton                  PAiA Electronics, Inc
> 3200 Teakwood Ln.              honcho at paia.com
> Edmond OK 73013                http://www.paia.com
> 405-340-6300                   fax 405-340-6378



More information about the Synth-diy mailing list