<div dir="ltr"><div><a href="http://musictechnologiesgroup.com/blog/?p=257">http://musictechnologiesgroup.com/blog/?p=257</a></div><div><br></div><div>CR2032 battery holders don't fit the footprint of the old CR2032s with solder tabs.  I recommend getting some of those PCBs in the link above ordered and installing a battery holder in its place.  Then next time you need to replace the battery you don't need a soldering iron.</div></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Tue, Sep 1, 2026 at 9:31 PM Jimmy Moore via Synth-diy <<a href="mailto:synth-diy@synth-diy.org">synth-diy@synth-diy.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">Thank you!!!  just removed mine.<div><br></div><div>Syntaur looks to be backordered with replacements.  can anyone recommend an alternative solution?  Preference for a battery that isn't spot welded to the clip.</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 1, 2026 at 2:06 PM Richie Burnett <<a href="mailto:rburnett@richieburnett.co.uk" target="_blank">rburnett@richieburnett.co.uk</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Just changed the battery in my Roland Alpha Juno 2 that was likely 40 years <br>
old!  The old Sanyo CR2032 coin cell looked fine from the top (+) side, <br>
measured 3.295v and hadn't shown any battery warning message on the synth's <br>
display.  In fact it's terminal voltage was higher than my brand new <br>
Panasonic CR2032s that both measured 3.278v.  However, when I de-soldered it <br>
the hidden underside was covered in tiny crystals and green crud (>.<) <br>
Looks like I got there just in time!  So, don't wait for the low battery <br>
message, or visible corrosion, and don't wait for 40 years before changing <br>
it!!!<br>
<br>
For anyone with an Alpha or MKS-50 there's an excellent step-by-step guide <br>
here:<br>
<br>
<a href="https://llamamusic.com/mks50/MKS-50_battery_replacement.html" rel="noreferrer" target="_blank">https://llamamusic.com/mks50/MKS-50_battery_replacement.html</a><br>
<br>
-Richie,<br>
<br>
<br>
-- <br>
This email has been checked for viruses by AVG antivirus software.<br>
<a href="http://www.avg.com" rel="noreferrer" target="_blank">www.avg.com</a>________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>
________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>