<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8">
</head>
<body style="overflow-wrap: break-word; -webkit-nbsp-mode: space; line-break: after-white-space;">
Hi Nathan,
<div><br>
</div>
<div>Thanks for pinging me back.</div>
<div>(answers inline)<br id="lineBreakAtBeginningOfMessage">
<div><br>
<blockquote type="cite">
<div>On Apr 16, 2025, at 5:59 PM, Nathan <nathan@idmclassics.net> wrote:</div>
<br class="Apple-interchange-newline">
<div>
<div dir="ltr">Hi Eric,
<div><br>
</div>
<div>By "two highest gate ICs" do you mean the 413 and 414 (the highest octave for 4' and 8' respectively)? 413 is only used in the Violin, and 414 in the Viola. </div>
</div>
</div>
</blockquote>
<div><br>
</div>
Correct.</div>
<div><br>
<blockquote type="cite">
<div>
<div dir="ltr">
<div>Since you still get the bleed when only one of those is installed, and presumably if one of those switches is on and the other isn't, then the big thing they have in common are the RC trigger networks ("sustain circuits") for each note before they go to
the gate ICs. If any keys have a bad cap/resistor in the trigger path, or a bad gate IC, then the gates on the chip could stay partially open. Every time you play a key and the main VCA opens, you'll hear that droning. Issues with the sustain voltage or bad
caps on other notes can also interact with that.</div>
</div>
</div>
</blockquote>
<div><br>
</div>
I just pulled those two IC’s as an example. There’s note bleeding for any note across the keyboard.</div>
<div><br>
<blockquote type="cite">
<div>
<div dir="ltr">
<div>I'd definitely check the caps on that octave. If you check the voltage at the signal side of the 15uF cap for each of those keys, you may find that some are higher than others, or the droning disappears when you probe. </div>
</div>
</div>
</blockquote>
<div><br>
</div>
I measured voltages at the signal side of all 49 caps, and they’re all sitting right at -6.0V, +/- 0.01V. Hitting the appropriate key drops the voltage to -15V. BUT, if I hit any other key than the one I’m measuring, I can see the voltage on the one I”m measuring
drop to -7 or -8V or so over the span of a couple of seconds. It’s like this, to varying degrees, on the whole keyboard, and playing chords makes the voltage drop faster.</div>
<div><br>
</div>
<div>Do I have 49 bad caps?!</div>
<div><br>
</div>
<div>e</div>
<div><br>
<blockquote type="cite">
<div>
<div dir="ltr">
<div>Best,</div>
<div><br>
</div>
<div>Nathan</div>
</div>
<br>
<div class="gmail_quote gmail_quote_container">
<div dir="ltr" class="gmail_attr">On Wed, Apr 16, 2025 at 2:24 PM Eric Frampton <<a href="mailto:eric@ericframpton.com">eric@ericframpton.com</a>> wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<div>
<div>Hey y’all -</div>
<div><br>
</div>
<div>I’m back at my never-ending Solina project, and am down to one last (big) issue.</div>
<div>This is a Series 33, so 1975-ish with the Gate and Trigger jacks in the back and the Chorus switch on the front.</div>
<div><br>
</div>
<div>When I play a key, I hear not only the selected waveform from the key, but also some or all (hard to tell) of the other keys droning quietly in the background. If I play multiple keys, the droning is louder. The drones follow the VCA envelope.</div>
<div><br>
</div>
<div>If I scope the output for the highest gate chip for the highest 10 notes, and play the top C and work my way downward, I get the waveform for the C down to D# (as you’d expect), then silence/no waveform, then starting at the G (G2?) that is the top of
the bass/cello section, I start getting lower amplitude waveforms all the way to the bottom C.</div>
<div><br>
</div>
<div>For troubleshooting, I removed and socketed the two highest gate IC's. If I remove those and do the same test, I get silence on those top 10 notes (as you’d expect), then no added waveforms at all going down the keyboard.</div>
<div><br>
</div>
<div>The added waveforms I’m hearing seem to be from the main Gate board, and not the Bass board, based on pitch. They show up in all four 4’ and 8’ sounds (viola, violin, trumpet, horn) but not in the Cello or Bass - those two seem to be fine.</div>
<div><br>
</div>
<div>i’ve got trimmer on the Gate board adjusted for 15V. If I lower it (say, to the point of voices not starting to speak), the drones are still there, they’re just lower in volume.</div>
<div><br>
</div>
<div>Here’s a link to the schematics: <a href="https://manuals.fdiskc.com/flat/ARP%20Solina%20Schematics.pdf" target="_blank">https://manuals.fdiskc.com/flat/ARP%20Solina%20Schematics.pdf</a></div>
<div><br>
</div>
<div>any ideas?</div>
<div><br>
</div>
<div>thanks,</div>
<div>e</div>
<div><br>
</div>
</div>
________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">
https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">
https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">
marketplace@synth-diy.org</a><br>
</blockquote>
</div>
</div>
</blockquote>
</div>
<br>
</div>
</body>
</html>