<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD><TITLE>Re: [sdiy] Buchla Lowpass Gate Switch</TITLE>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 5.50.4926.2500" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT face=Arial size=2>Hey Peter,</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Pretty interesting - I'd never actually examined
Rev 2 that much. Glancing at it, though, how does it work for the 'Both'
mode? I only see two positions for the switch.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>FWIW, I have not experienced any noticeable leakage
through my LPG. I wonder if the luck of the draw of Vactrols has anything
to do with it. I did use only the required parts - I left out all the
computer interface stuff.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>BTW, if you (or anyone else) could be so kind could
you please explain to me what in the world that CV is doing in the 266 SOU
Stored Random Voltage circuit? It's driving me nuts - I understand
everything on the SOU but that one section (what's with that bridge rectifier in
the feedback of that op amp)? </FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Just curious...I'll know sooner or later after I
breadboard it, but I reiterate - it's driving me nuts!</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Take care,</FONT></DIV>
<DIV><FONT face=Arial size=2>Scott</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<BLOCKQUOTE
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=peter@buzzclick-music.com
href="mailto:peter@buzzclick-music.com">Peter Grenader</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=scottnoanh@peoplepc.com
href="mailto:scottnoanh@peoplepc.com">Scott Stites</A> ; <A
title=peng3002@yahoo.com href="mailto:peng3002@yahoo.com">Peng</A> ; <A
title=synth-diy@dropmix.xs4all.nl
href="mailto:synth-diy@dropmix.xs4all.nl">synth-diy@dropmix.xs4all.nl</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Tuesday, August 10, 2004 9:52
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: [sdiy] Buchla Lowpass Gate
Switch</DIV>
<DIV><BR></DIV>Scott Stites wrote:<BR><BR><FONT size=2><TT>Peter Grenader
devised a method to avoid using the 4016's at all by installing a (IIRC) 3PDT
center off switch, which makes things a bit easier. However, I am using
Mark's adaptation of the Low Pass Gate using the 4016 mainly because 4016's
are a helluva lot cheaper than those 3PDT switches (but that's just
me).<BR></TT></FONT><BR><BR>Yes, that would be me. <BR><BR>I lost the
analog switch and just went with a triple pole basically because I was lazy.
That being said though, remember - the only reason Don used an analog
switch on the rev C was for the other sections of that component that Mark
didn't need to incorporate that allowed rev C to be computer controlled.
If you notice the rev 2 doesn't use them and in fact only requires a
double pole, which saves you a few $$.<BR><BR></BLOCKQUOTE></BODY></HTML>