<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta http-equiv="Content-Type" content="text/html;charset=ISO-8859-1">
<title></title>
</head>
<body text="#000000" bgcolor="#ffffff">
Yes, you would expect a small signal at the 3080's inputs - there is a
100k to 220 ohm divider there. The 3080's can only handle a small
signal of 30mV or so without distortion.<br>
<br>
<br>
Frederic Bourgeais wrote:<br>
<blockquote type="cite" cite="midBC5FC305.5867%25fred@upian.com">
<pre wrap="">Merci yves pour cette reponse si rapide,
En branchant un petit HP sur l'entrée non inverseuse, j'obtiens mon signal
audio, fortement atténué, mais y a t'il une limite de fonctionnement minimum
avec le 3080 ?.. Je regarderai ce soir si il n'y a pas un probleme autour de
O1..
Merci :)
Same below in english:
I have a smallest audio signal on inv.input of O1, after input resistors,
but is it too low to work with 3080 ?
-------------------
To Daniel:
Ok, So I'll I had to swap all connections going to - input of O2 with the +
one.. Hum it will be tricky, my board is very small !
Thanks for your help !
</pre>
<blockquote type="cite">
<pre wrap="">De : Yves Usson <a class="moz-txt-link-rfc2396E" href="mailto:yves.usson@imag.fr"><yves.usson@imag.fr></a>
Date : Mon, 23 Feb 2004 14:18:30 +0100
À : Frederic Bourgeais <a class="moz-txt-link-rfc2396E" href="mailto:fred@upian.com"><fred@upian.com></a>
Objet : Re: [sdiy] MS20 VCF clone troubles
Bonjour Frédéric
D'après ce que tu dis on peut supposer une chose :
il y a une interruption de circuit entre la 10k d'entrée et l'entrée
inverseuse
de O1 ou elle est à la masse. Pour vérifier cela, il faut brancher un
oscillo directement sur
la boche 2 de OP1 (entrée inverseuse) et voir si le signal d'entrée
est présent avec une atténuation de 50x (à défaut d'oscillo utiliser un
petit ampli
audio). Si rien n'est présent ou audible, vérifie que la 22à ohm n'est
pas en court-circuit
avec la masse. Si ce n'est pas le cas tester que la broche 3 de O1 est
à un
potentiel de 0V (c-a-d que la 220 ohm est bien connecté à la masse).
Voilà j'espère que cela pourra résoudre ton problème !
Bonne chance.
Yves
Le lundi, 23 fév 2004, à 13:41 Europe/Paris, Frederic Bourgeais a écrit
:
</pre>
<blockquote type="cite">
<pre wrap="">Hello All,
I build René Schmitz's MS20 vcf which can be found here:
<a class="moz-txt-link-freetext" href="http://www.uni-bonn.de/~uzs159/rs20.png">http://www.uni-bonn.de/~uzs159/rs20.png</a>
I have some troubles, all components value and connections has been
checked
and rechecked.. Can you help me for debbugging ?
When no audio input is connected, Cutoff and resonnance pots seems to
work.
I can heard the modulation on background noise, and the filter self
oscillate if I play with resonnance pot.
When I input audio signal into O1 inv.input, the signal don't seems to
go
throw O1 output. I can heard again the modulation on background noise,
and
filter can still self oscillate, but he don't process my input
source...
I swapped all 3080 with new ones, but no way.. If I put audio in
directly on
O1 output, or on A3 the filter seems to work..
Should I hear input signal at O1 output (I think ) ? 3080 are
connected to
-15/+15, but i didn't linked the bias amplifier input (pin 5).. Should
I
ground it ?
All the schematics has been build except CV2 input, and "Pitch input".
what's the difference between externals CV and pitch input ? What kind
of
signal should I put in, ( voltage I believe, but can I leave them
unplugged
) ?
I didn't use any CV source or pitch input, because 47k lin pot
connected to
+15/-15 seems control the input voltage. Does this circuit can work
like
that or I missed something ?
Thanks
Fred
</pre>
</blockquote>
<pre wrap="">-------------------------------------------------------------
Yves Usson
Lab. TIMC UMR5525 CNRS
Institut d'Ingéniérie et de l'Information de Santé (IN3S)
Faculté de Médecine
Domaine de la Merci
38706 La Tronche cedex
email : <a class="moz-txt-link-abbreviated" href="mailto:yves.usson@imag.fr">yves.usson@imag.fr</a>, <a class="moz-txt-link-abbreviated" href="mailto:yves.usson@ujf-grenoble.fr">yves.usson@ujf-grenoble.fr</a>
tel. (+33) (0)456 520 074
fax. (+33) (0)456 520 022
</pre>
</blockquote>
<pre wrap=""><!---->
</pre>
</blockquote>
<br>
<pre class="moz-signature" cols="72">--
Scott Bernardi
<a class="moz-txt-link-abbreviated" href="mailto:sbernardi@comcast.net">sbernardi@comcast.net</a></pre>
</body>
</html>