<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2713.1100" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT size=2>yes, i would be too.. after reading all those articles about
the chip, i'd like to build another synth around one.. the one i made earlier
was a pre-made circuit that i modified, but it's not all working that well
anymore.. i'd definitely be interested in a few chips..</FONT></DIV>
<DIV><FONT size=2></FONT> </DIV>
<DIV><FONT size=2>ruud</FONT></DIV>
<DIV><FONT size=2></FONT> </DIV>
<BLOCKQUOTE
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=Bobinvertedsdiy@aol.com
href="mailto:Bobinvertedsdiy@aol.com">Bobinvertedsdiy@aol.com</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A title=john@blacet.com
href="mailto:john@blacet.com">john@blacet.com</A> ; <A
title=synth-diy@dropmix.xs4all.nl
href="mailto:synth-diy@dropmix.xs4all.nl">synth-diy@dropmix.xs4all.nl</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Wednesday, November 20, 2002 2:51
AM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: [sdiy] 76477 "N" vs
"NF"</DIV>
<DIV><BR></DIV><FONT face=arial,helvetica><FONT lang=0 face=Arial size=2
FAMILY="SANSSERIF">In a message dated 11/19/2002 8:06:16 PM Eastern Standard
Time, <A href="mailto:john@blacet.com">john@blacet.com</A> writes:<BR><BR><BR>
<BLOCKQUOTE
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #0000ff 2px solid; MARGIN-RIGHT: 0px"
TYPE="CITE"><BR>Thanks to everyone for all the
suggestions!<BR><BR>Unfortunately the .070 pitch looks a lot more like SMT
than DIP. I would<BR>hate to solder anything to those pins. If I had to, I
would bend up<BR>every other pin to give some room for soldering.<BR><BR>The
difference in width from the "N" to "NF" is only 0.2", leaving only<BR>0.1"
on each side to run traces if you were going to design an adaptor<BR>board.
It would have to be doublesided and it would be a challenge.<BR><BR>I guess
these go back to the vendor.<BR><BR>Anybody want 100 brand new shiny
76477NF?<BR><BR>Regards,<BR>--/////--<BR>John Blacet<BR>Blacet
Research<BR>http://www.blacet.com<BR><BR></BLOCKQUOTE><BR><BR>Anybody want
100? Probably not, but I'm sure there are quite a few people who would like
one or two. Would you consider selling them individually at a small profit?
<BR><BR>Robert </FONT></FONT></BLOCKQUOTE></BODY></HTML>